Abstract:Fe-6.5wt% Si non-oriented electrical steel sheets with a thickness of 0.50mm were produced by using a new processing route: strip casting followed by hot rolling, intermediate temperature (150–850°C) rolling and final annealing. The present study focused on exploring the effects of rolling temperature varying from 150 to 850°C on the microstructure and texture evolution, the formability and final magnetic properties. The microstructure and texture evolution at the various processing steps were investigated in detail by using OM, XRD, EBSD and TEM. It was found that the formability during rolling, the microstructure and texture before and after annealing and final magnetic properties highly depended on rolling temperature. The formability during rolling was gradually improved with increasing rolling temperature due to the slipping of dislocation. In particular, the rolling temperature dominated the formation of in-grain shear bands in the rolled microstructure, which played an important role in the development of final recrystallization microstructure and texture. In the case of lower temperature (150–450°C) rolling, an inhomogeneous microstructure with a large amount of in-grain shear bands was formed in the rolled sheets, which finally resulted in a fine and inhomogeneous annealing microstructure dominated by mild λ-fiber texture composed of cube and {001}〈210〉 components and α*-fiber texture concentrated on {115}〈5–10 1〉 component. By contrast, in the case of higher temperature (650–850°C) rolling, a relatively homogeneous microstructure without in-grain shear bands was formed instead in the rolled sheets, which finally led to a coarse and relatively homogeneous annealing microstructure characterized by strong α-fiber and γ-fiber texture. Accordingly, on the whole, both the magnetic induction (B8 and B50) and iron loss (P15/50 and P10/400) decreased with raising rolling temperature.

Effect of Cold Rolling Reduction on Texture and Properties of Cast-rolled Aluminum Strip under Electromagnetic and Ultrasonic Field

Microstructures and textures in cold-rolled aluminium strip

Effects of Compound Energy Field on Microstructure and Mechanical Properties of Roll-Casted AZ61 Magnesium Alloy Strip

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel

Effect of cold rolling reduction on microstructure, mechanical properties, and texture of deep drawing dual-phase (DP) steel

Effects of Hot-Rolling Reduction on Microstructure, Texture and Magnetic Properties of High Silicon Steel Produced by Strip Casting

Effect of Microstructures on the Anisotropy of the Roll Casting Strip of Cold Rolled 3003 Aluminum Alloy

Effect of rolling reduction on microstructure, texture, mechanical properties and mechanical anisotropy of AZ31 magnesium alloys

Mg–3Al–1Zn alloy strips processed by electroplastic differential speed rolling

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Microstructure and Texture Evolution in Cold-Rolled and Annealed Oxygen-Free Copper Sheets

Effects of Warm Temper Rolling on Microstructure, Texture and Magnetic Properties of Strip-Casting 6.5wt% Si Electrical Steel

Effects of rolling temperature on microstructure, texture, formability and magnetic properties in strip casting Fe-6.5wt% Si non-oriented electrical steel

An Investigation on Rolling Texture Transition in Copper Preprocessed by Equal Channel Angular Pressing

Effect of Hot Rolling on Microstructures and Mechanical Properties of SiCp/A356 Aluminum Matrix Composites

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

Effect of Current Frequency on the Mechanical Properties, Microstructure and Texture Evolution in AZ31 Magnesium Alloy Strips During Electroplastic Rolling

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Effects of cold-pre-rolling reduction on precipitation of 2519A aluminum alloy plate