Abstract:The present study investigated the aging precipitation behavior and mechanical, electrical properties of Cu–15Ni–8Sn alloy affected by cold rolling with different deformations. During cold rolling, the grain is elongated gradually along rolling direction with increasing deformation, simultaneously accompanied by the occurrence of a great deal of dislocations and deformation twins. During aging process, the coherent DO22 and L12 ordered phases precipitate successively from the matrix after 90% rolling deformation and aging treatment at 400 °C for 0.5 h with the orientation relationship of <math>(1¯10)DO22</math> // <math>(022¯)Cu</math>, <math>[111]DO22</math> // <math>[211]Cu</math>; <math>(11¯1¯)L12</math>// <math>(11¯1¯)Cu</math>, <math>[211]L12</math> // <math>[211]Cu</math>. However, discontinuous precipitation (DP) behavior is significantly accelerated by prior cold rolling. On the one hand, by revealing the underlying growth kinetics of DP, it can be found that the nucleation sites of DP transform from grain edges to grain boundaries gradually with increasing rolling deformation. On the other hand, the nucleation sites and nucleation rate of DP can be enhanced greatly with increasing dislocation density. Furthermore, the interlamellar spacing of DP slightly increases and the morphology transforms from lamellar structure to bush-like structure gradually with increasing rolling deformation. In addition, the hardness, tensile strength and electrical conductivity are obviously improved while the peak aging time greatly shortens with increasing rolling deformation. The optimal combination of properties with a hardness of 409 HV, a yield strength of 1256 MPa, and an electrical conductivity of 7.5 %IACS can be obtained in the sample with 90% rolling deformation after aging treatment at 400 °C for 0.5 h. The corresponding strengthening mechanism and conductive mechanism were discussed. It can be discovered that the precipitation strengthening, dislocation strengthening and solid solution strengthening are believed to be the main strengthening mechanisms to enhance the alloy strength.

Effects of cold-pre-rolling reduction on precipitation of 2519A aluminum alloy plate

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Effect of cold rolling reduction on the precipitation behavior of σ phase in 2906 duplex stainless steel

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Precipitation kinetics of 2519A aluminum alloy based on aging curves and DSC analysis

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of cold rolling pre-deformation on microstructure and properties of V-1469 Al-Li alloy

δ-phase precipitation regularity of cold-rolled fine-grained GH4169 alloy plate and its effect on mechanical properties

Effect of pre-rolling path on mechanical properties of rolled ZK60 alloys

Effect of annealing process on microstructure and mechanical properties of precipitated phase of A1235 aluminum alloy

Effects of Cold Rolling Reduction Rate on the Microstructure and Properties of Cu-1.16Ni-0.36Cr Alloy after Thermo-Mechanical Treatment

Improving Precipitation in Cryogenic Rolling 6016 Aluminum Alloys during Aging Treatment

Effects of Cold Rolling Pre-Strain on Abnormal Grain Growth Behavior in Longitudinal Welds of 2196 Al-Cu-Li Profiles

Effect of 90% cold rolling on precipitation behavior of Al-0.6Mg-1.0Si-0.5Cu alloy

Effect of cold rolling on aging precipitation behavior and mechanical properties of Cu–15Ni–8Sn alloy

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Effect of cold rolling reduction on microstructure, mechanical properties, and texture of deep drawing dual-phase (DP) steel

Effect of recrystallization annealing, solid solution and pre-aging intermediate treatment on microstructure and mechanical properties of Al-Mg-Si rolled sheet

Enhanced formability of Al–Mg–Si–Zn alloy sheet via dislocation structure and texture during cold rolling