Abstract:The research on Al–Zn–Mg–Cu alloys mainly focuses on the effects of solution aging and strain rate on the microstructure and properties of the alloy, as well as the flow stress behavior of the alloy. There are few studies on the effects of hot rolling deformation and reduction pass on the microstructure and properties of aluminum alloy. The dislocation density of alloy is affected by changing the rolling deformation, and post-heat treatment improves fine grains segregation and break coarse second phases. The alloys comprehensive mechanical properties are improved by controlling the recrystallization fraction and size. Different shape variable rolling and different passes, optical microscope (OM), field emission scanning electron microscope (SEM) with energy dispersive spectrometers (EDS), X-ray diffractometer (XRD), microhardness tester, and other methods were used to characterize the samples, and simulation of the rolling process analyzed by Deform-3D software. The effects of hot rolling deformation and deformation pass on microstructure and properties of aluminum alloy were also studied. The results show that dynamic recrystallization was beneficial to grain refinement when deformation increases to 40%. The coarse second phase was broken and refined into chains and partially spheroidized to dissolve in the matrix under large deformation. Dislocation density decreased after solution treatment when deformation was less than 80%, and increased after large deformation was 80%. The equivalent strain obtained by numerical simulations increases with the increase of deformation. The maximum equivalent strain was on both sides of the rolling surface, and this area was the most prone to crack in rolling. When the increase of the shape variable, the recrystallization volume fraction increased, and the grain size decreased.

Effect of pre-rolling path on mechanical properties of rolled ZK60 alloys

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Effect of cold rolling on microstructure and mechanical properties of pure Zr

Effect of Multi-Path Asynchronous Rolling Process on Microstructure and Mechanical Properties of ZK60 Magnesium Alloy

Effects of Cold Rolling Pre-Strain on Abnormal Grain Growth Behavior in Longitudinal Welds of 2196 Al-Cu-Li Profiles

Effect of Deformation Mode on Grain Characteristics and Strength–Toughness of Al-Zn-Mg-Cu Alloy

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Effects of pre-compression modes on mechanical properties and fatigue behaviors of rolled ZK60 magnesium alloy

Effects of Hot Rolling Process Conditions on Microstructure and Mechanical Properties of Hot-rolled Al-Zn-Mg-Cu-Sc-Zr Alloys

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Elucidating the effects of cold rolling route on the mechanical properties of AISI 316L austenitic stainless steel

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy

Effect of rolling on the structure and mechanical properties of the Zn-0.8Li alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

The effect of grain size on texture evolution and mechanical properties of an AZ31 magnesium alloy during cold-rolling process

Enhanced formability of Al–Mg–Si–Zn alloy sheet via dislocation structure and texture during cold rolling

Microstructural and textural differences between rolled Zr702 and Zr-2.5Nb alloys: The role played by preexisting β phase

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy