Abstract:Phase change materials (PCMs) are widely employed in electronic thermal control systems for spacecraft because of their substantial energy storage competencies. Hence, the impact of gravitational acceleration (GA) on PCM thermal performance holds particular significance. Moreover, given considerations for spacecraft center of gravity, attitude control, and structural design, choosing an optimal battery placement orientation becomes pivotal for maximizing available space utilization. This study employs the enthalpy-porosity method to simulate and assess the heat transfer efficiency of PCM and the thermal behavior of cooling battery thermal management system (BTMS) under different gravity environments (0.05 g, 0.1 g, 1 g, 10 g, and 20 g) and different inclination angles ( θ = 90°, 45°, 0°). The research findings indicate that when θ = 90°, as gravity increases from 0.05g to 20g, the complete melting time of PCM at GA = 20g is shortened by 95.05 s (15.00 %) compared to GA = 0.05g. Particularly, when GA = 10 g, increasing θ from 45° to 90° reduces PCM melting time by 59.05 s (9.66 % reduction) compared to θ = 45°, while at θ = 0°, it decreases by 65.75 s (10.75 % reduction). Notably, at θ = 45°, some unmelted solid PCM accumulates in the lower right corner of the enclosure hindering the BTMS heat transfer. Based on PCM melting characteristics, three optimization structures for different θ are proposed. At t = 240 s, PCM melting significantly improves with fins. Comparing Convective Heat Transfer Coefficients (CHTC) curves before and after optimization reveals reduced accumulated effects. However, more fins aren't always better due to BTMS weight considerations. Investigating enhanced CHTC, fin mass, and volume ratio( γ ), the optimized model impacts BTMS weight differently for θ values. θ = 45°, a combination of annular and straight fins, is determined optimal using entropy-weighted TOPSIS. This paper innovatively studies PCM melting in BTMS under varied gravitational environments and θ , proposing an enhanced heat transfer scheme for aerospace BTMS design.

Conditional Extremum Optimization Analyses and Calculation of the Active Thermal Control System Mass of Manned Spacecraft

Global Mass Optimization of Spacecraft Thermal Control Loop

Mass Optimization of Thermo Hydraulic Network of Manned Spacecraft Environment Control and Life Support System

Design and Optimization for Fluid Loops of Active Thermal Control System in Manned Spacecraft

Optimization of Thermal Network for Spacecraft Thermal Control and Environment Control and Life Support System

The Lightweight Design for the Parallel Loops in the Thermal Control System of Manned Spacecraft

Dynamic optimization analyses and algorithm design for the parallel heat exchange system in spacecraft

Optimization of the aero-engine thermal management system with intermediate cycle based on heat current method

Minimization of mass for heat exchanger networks in spacecrafts based on the entransy dissipation theory

Ptimization of the Thermal Network in Parallel Connection of Manned Spacecraft

Optimization strategy of active thermal control based on Kriging metamodel and many-objective evolutionary algorithm for spaceborne optical remote sensors

Simulation and Optimization of Cryogenic Air Separation Units Using a Homotopy-Based Backtracking Method

Trajectory Optimization Method of Aero-Gravity Assist Orbital Maneuver

Efficiency and Mass Optimization for Space Nuclear Power Systems with Closed Brayton Cycle Loops

Thermal-mechanical coupling analysis and optimization design on tps with gap

Analysis of Mass Minimization of Thermoelectric Integrated Membrane Evaporation Subsystem in Waste Water Processing

Thermal-Mechanical Coupling Analysis and Structural Optimization of a Deployable Grasping Manipulator

Numerical study and optimization of battery thermal management systems (BTMS) Based on Fin-Phase change material (PCM) in variable gravity environments

Optimization method of the thermal control index of space remote sensors based on force-thermal coupling algorithm

Quasi-All-Passive Thermal Control System Design and On-Orbit Validation of Luojia 1-01 Satellite

Optimization Of Control Parameters Based On Multi-Objective Genetic Algorithms For Spacecraft Attitude Tracking Control