Abstract:Neat well cement experience significant strength retrogression at high temperatures above 110 °C, especially at approximately 150 °C. To reveal the mechanism of performance degradation and guide the preparation of high-performance cement, we investigate the hydration process, mechanical behavior, and fracture process for well cement at the temperature of 150 °C based on molecular dynamics simulations and experiments. From triaxial pressure tests and Brazilian splitting tests, the strength, elastic modulus, and Poisson's ratio of well cement decrease drastically with temperature increases from 80 °C to 150 °C. According to XRD, TG/DTG/DSC, and SEM, the hydration degree is insufficient, and larger pores exist in the microstructures. As the main binding phase of well cement, the mechanism of calcium silicate hydrates (C-S-H) influenced by curing temperatures is investigated through molecular dynamics simulations. C-S-H with calcium/silicon ratios (C/S) of 1.1 and 1.8 are simulated in the aqueous and solid states to investigate precipitation and mechanical behaviors. By reducing the C/S ratio to 1.1, the strength rebounds to a certain extent, and the adequacy of the hydration degree improved. It is found from the polymerization process that the increasing temperature promotes the polymerization rate, which is higher with C/S = 1.8 than that of 1.1. However, an increase in the C/S ratio will lead to a decrease in bridging oxygen content, thus a lower polymerization degree. The fracture simulations of C-S-H gels at different temperatures indicate that the failure of the C-S-H structure is mainly attributed to the disassembling of the calcium oxygen layers. With a higher temperature, there are fewer Ca-O bonds breaking, thus less strain energy consumed, resulting in worse performance. The elasticity of C-S-H, including Young's and shear moduli, also exhibits certain degradations at a higher temperature. The elastic behavior of C-S-H with a low C/S ratio is generally higher than the high C/S.

High temperature properties of silica sol-gangue shell and its mechanism analysis

High temperature behavior of silica sol shell and its influencing factors

EXPERIMENTAL STUDY ON THE PHASE RELATIONS OF THE SYSTEM Mg2SiO4-MgAl2O4 AT HIGH PRESSURE AND HIGH TEMPERATURE

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

Effect of Sintering Temperature on Microstructure and Mechanical Behavior of Alumina-Based Ceramic Shell by SLS

Microstructure evolution and bonding mechanisms of silica sol bonded coating at elevated temperatures

High-temperature properties of Al 2 O 3 /SiO 2 composites

Effect Of Silica Sol On The Properties Of Alumina-Based Duplex Ceramic Cores

Experimental Study on Mechanical Properties of Silica-Based Ceramic Core for Directional Solidification of Single Crystal Superalloy

Hot strength and microstructure of β-sialon-Al2O3-SiC composites

Microstructure Evolution and Mechanical Behaviors of Alumina-Based Ceramic Shell for Directional Solidification of Turbine Blades

Atomic-level Sintering Mechanism of Silica Aerogels at High Temperatures: Structure Evolution and Solid Thermal Conductivity

High Temperature Mechanical Property of Al2O3 Coated Quartz-Fiber Reinforced Methyl Silicon Resin Composites

Temperature-Induced Interfacial Change In Au@Sio2 Core-Shell Nanoparticles Detected By Extended X-Ray Absorption Fine Structure

Effect of silica sol on the properties of alumina-based ceramic core composites

Insight into Class G Wellbore Cement Hydration and Mechanism at 150 °C Using Molecular Dynamics

Formation and strengthening mechanisms of xonotlite in C3S-silica and C2S-silica powder systems under high temperature and pressure

High-temperature microtexture, microstructure evolution, and thermal insulation properties of porous Si3N4/silica aerogel composites produced by impregnation

Effect of in-situ formation of columnar mullite and pore structure refinement on high temperature properties of corundum casatbles

Strength Acquisition Mechanism of High Temperature Resistant Materials Prepared by Waste Architectural Ceramics

Study on Microstructure of the Silica Sol Investment Casting Shells