Abstract:Mechanical behaviors of a Ni-based single crystal superalloy have been investigated by tensile testing at various temperatures. Deformation substructures and mechanisms have been systemically revealed from micrometer to atomic scales by using advanced scanning electron and scanning transmission electron microscopes. Results show that deformation mode of the alloy strongly depends on the temperature due to competitive responses of the gamma and gamma' phases under mechanical loading and their original stress statuses. At temperatures from ambient to 750 degrees C, plasticity is governed by dislocation shearing in both phases, where slip modes of gamma are < 110 >{111} and those of gamma' are < 112 >{111}, < 110 >{111} and < 110 > {001}. At moderate temperatures (850 degrees C <= T <= 900 degrees C), plasticity mainly involves microscopically uniform deformation of both phases. The matrix deforms first so that channels parallel to tensile direction are narrowed due to the Poisson's effect, after that deformation of gamma' follows. The active slip modes are < 110 > {111} for gamma, < 112 >{111}, < 110 >{111}, < 110 >{001}, and < 001 >{001} for gamma'. At temperature higher than 1000 degrees C, plastic strain is also derived from deformation of both phases, but deformation of the matrix plays critical roles, due to relatively weak strength of this phase. The operative slip modes are < 110 > {111} for gamma, but mainly < 110 >{001} and < 001 >{001} for gamma'. Our results clearly provide a comprehensive and multiscale (from micrometer to atomic) understanding on the deformation mechanism of Ni-based superalloys, which can be critically beneficial and offer mechanistic guidelines to design new/next generation superalloys. (c) 2021 Elsevier Ltd. All rights reserved.

Experimental Study on Mechanical Properties of Silica-Based Ceramic Core for Directional Solidification of Single Crystal Superalloy

Mechanical Properties and Constitutive Model of Silica-based Ceramic Core for Directional Solidification of Single Crystal Superalloy

Effect Of Silica Sol On The Properties Of Alumina-Based Duplex Ceramic Cores

Effect of Sintering Temperature on Microstructure and Mechanical Behavior of Alumina-Based Ceramic Shell by SLS

Alumina-Based Ceramic Core Nano-Composites For Investment Casting

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

THIS ARTICLE HAS BEEN RETRACTED Effect of Silica Sol on the Properties of Alumina‐Based Duplex Ceramic Cores

Effect of silica sol on the properties of alumina-based ceramic core composites

Microstructure Evolution and Mechanical Behaviors of Alumina-Based Ceramic Shell for Directional Solidification of Turbine Blades

Microstructure and Crystallization Kinetics of Silica-Based Ceramic Cores with Enhanced High-Temperature Property

High-Temperature Mechanical Behaviors of SiO2-Based Ceramic Core for Directional Solidification of Turbine Blades

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Effect of Particle Size on Properties of Alumina-Based Ceramic Cores

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Experimental study on high temperature performances of silica-based ceramic core for single crystal turbine blades

Effect of Al(OH) 3 on the Properties of Silica-based Ceramic Cores Prepared by Laser Powder Bed Fusion Combined with Vacuum Infiltration

Changes in the microstructure and mechanical properties of Al2O3/YSZ directionally solidified eutectic ceramics during long-time heat treatment

Simulation and Experimental Study on the Directional Solidification Process of a Single Crystal Superalloy Plate Casting

Simulation and Experiments on Plasticity and Recrystallisation in SX Superalloys by Investment Casting

Microstructure and properties evolution of silicon-based ceramic cores fabricated by 3D printing with stair-stepping effect control

Influence of Al2O3 content on mechanical properties of silica-based ceramic cores prepared by stereolithography