Abstract:It is highly desirable to undercool titanium based alloy melts and modulate their dendritic solidification process due to the relevant applications in aerospace engineering. But the serious chemical reactivities of this category of alloys result in potent heterogeneous nucleation and suppress remarkable undercoolings in the course of normal material processing. This paper shows that such a challenge can be solved by containerless processing approach. Liquid Ti-25 wt.%Al alloy is highly undercooled and rapidly solidified under containerless state by both electromagnetic levitation and drop tube techniques. Its metastable undecoolability, crystal nucleation mechanism and dendrite growth process are examined experimentally and analyzed theoretically. Those heterogeneous nuclei with wetting angles above 60 are found to be quite difficult to eliminate even during levitation processing, thus reducing the undercoolability of this alloy. The maximum undercooling of bulk alloy melt reaches 210 K (0.11 TL). The thermodynamic driving force to initiate the nucleation of -Ti phase increases almost linearly with the enhancement of undercooling. The phase dendrite displays a growth velocity up to 11.2 m/s, indicating that the rapid solidification is realized at the relatively slow cooling rate of levitated alloy melt. With the increase of undercooling, phase dendrite experiences a kinetic transition from solute diffusion controlled to thermal diffusion controlled growth. Once undercooling exceeds 100 K, the nonequilibrium solute trapping effect brings about the practically desirable segregationless solidification. Nevertheless, the single condition of substantial undercooling is insufficient to suppress the solid state transformation of phase. It is decomposed into 2-Ti3Al phase plus a small amount of -TiAl compound after containerless solidification at levitated state. A more efficient approach to controlling and modulating the solidification microstructures is to utilize the coupled effects of high undercooling and rapid quenching, which proves to be feasible through the rapid solidification of alloy droplets inside drop tube. For those alloy droplets with diameters ranging from 77 to 1048 m, their cooling rates attain a maximum of 1.05105 K/s, and the predicted maximum undercooling is 227-778 K. In this case, phase dendrites are well refined and kept in a metastable state until ambient temperature. The heat transfer calculations indicate that the thermal radiation is the dominant cooling mechanism for the large alloy droplets above 690 m, whereas thermal convection becomes the major cooling mechanism for the small alloy droplets below 690 m. The microgravity condition during free falling does not show apparent effect on the microstructural formation of these alloy droplets.

cooling rate control and solidified microstructure of Al-7.7Ca eutectic alloy during aerodynamic levitation

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Rapid solidification of Ti-Al alloys under electromagnetic levitation condition

Interface velocity dependent solute trapping and phase selection during rapid solidification of laser melted hypo-eutectic Al-11at.%Cu alloy

Solidification Microstructure Evolution and Grain Refinement Mechanism under High Undercooling of Undercooled Ni90Cu10 Alloys

Surface wave phenomenon and microstructure evolution mechanism of electromagnetically levitated ternary Ti-Al-Fe alloy

Microstructure Formation of Al-Based Alloys in the Presence of Rare Earth Metals (Ce, La) and Mn under High Cooling Rate

Substantial undercooling and rapid dendrite growth of liquid Ti-Al alloy

Thermophysical properties and rapid solidification mechanism of liquid Zr 60 Ni 25 Al 15 alloy under electrostatic levitation condition

Solidification Microstructure Evolution in LA42 Mg Alloy under Various Cooling Rates

Microstructure and solidification behaviour of Ni3Al/Ni7Hf2 eutectic alloy

In-situ observations of solidification process of Fe–Al–Ta eutectic alloy

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

A numerical study of irregular eutectic in Al-Si alloys under a large undercooling

Prediction of the Solidification Path of Al-6.32cu-25.13mg Alloy by A Unified Microsegregation Model Coupled with Thermo-Calc

Rapidly Solidified Structure of Aluminum Containing Lithium.

Microstructual evolution in Ti-185 alloy prepared using electrostatic levitation and conventional casting techniques

Prediction of the Solidification Path of Al-4.37cu-27.02mg Ternary Eutectic Alloy with A Unified Microsegregation Model Coupled with Thermo-Calc

Study on the eutectic and post-eutectic reactions in LM13 aluminum alloy using cooling curve thermal analysis technique

Isothermal Solidification of Micro Layers of Molten Aluminum Alloys

SOLIDIFICATION BEHAVIOR AND MICROSTRUCTURE EVOLUTION OF Fe83B17 EUTECTIC ALLOY UNDER HYPER-UNDERCOOLING