Abstract:As the construction and modernization of global navigation satellite systems (GNSS), in the near future, the four main navigation systems (GPS, BDS, GLONASS and GALILEO) as well as some regional systems such as QZSS and IRNSS will broadcast many signals in different frequency. Some of the signals may need further adjustment. In interim, the traditional hardware GNSS receivers which have high integration density and low flexibility are not suited for signals monitoring especially for those new signals.In order to meet the requirement of monitoring GNSS signals as well as the joint processing of them, a high-flexibility multi-system full-band real-time GNSS software receiver is developed. In addition to a wideband antenna, a RF front-end and a data acquisition card to fulfill down-conversion and AD conversion, the rest of receiver are implemented in an ordinary PC with a GPU. With efficient acquisition and tracking methods, the proposal receiver can process all of the civil signals from four main GNSS and some of the regional systems in real-time, including GPS L1C/A, L2C, L5, L1C, BDS B1, B2, GLONASS Gl, G2, GALILEO ElOS, E5a, E5b, QZSS L1C/A, L2C, L5, and L1C signals. Based on the software architecture, the receiver can provide PVT results, measurement results, and many intermediate data such as correlator outputs and raw bit stream which are necessary for signals monitoring and performance analysis. Meanwhile, the strong flexibility of this receiver makes it easy to expansion and update in the future. The GLONASS modernized signals as well as BDS Phase III signals can be quickly added to current receiver after the release of their interface control document (ICD).By using the proposed software receiver, this paper presents the real-time tracking states of all civil signals, the positioning results of each navigation signal, and the monitoring results of viable GNSS satellites. Finally, since the receiver can handle all the civil GNSS signals in real-time and has a flexible structure, it can be used as a dedicated development platform for various types of navigation research.

A 180nm fully-integrated dual-channel reconfigurable receiver for GNSS interoperations

An Asymmetric Dual-Channel Reconfigurable Receiver For Gnss In 180nm Cmos

A Dual-Channel GPS/Compass/Galileo/GLONASS Reconfigurable GNSS Receiver in 65nm CMOS

A Dual-Channel Compass/GPS/GLONASS/Galileo Reconfigurable GNSS Receiver in 65 Nm CMOS with On-Chip I/Q Calibration.

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A Multi-Mode Blocker-Tolerant GNSS Receiver with CT Sigma-Delta ADC in 65nm CMOS

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A K-Band Eight-Element Dual-Beam Receiver with Current-Sharing-Based Low-Power Technique for LEO SATCOM in 65-Nm CMOS

A C-Band Compact High-Linearity Multibeam Phased-Array Receiver With Merged Gain-Programmable Phase Shifter Technique

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A 90-98-ghz FMCW Radar Transceiver Supporting Broadband Modulation in 65nm CMOS

A Tri-Mode Reconfigurable Receiver for GNSS/NB-IoT/BLE with 68-Db HR3 and 60-Db IMRR in 28-Nm CMOS

A Multi-Mode Reconfigurable Analog Baseband With I/Q Calibration For Gnss Receivers

A low power triple-mode parallel-processing CMOS receiver for BD-II/GPS/Galileo joint navigation applications

An Interference-Robust Reconfigurable Receiver with Automatic Frequency-Calibrated LNA in 65-Nm CMOS

A Fully Integrated Low-Power Multi-Mode RF Receiver for BDS-3/GPS

Starx A Gpu Based Multi-System Full-Band Real-Time Gnss Software Receiver

Architecture And Implementation Of Gnss Software Receiver For Compatibility And Interoperability Research

Four-channel broadband compact multi-antenna GNSS downconverter for high-reliability navigation

NaviSoC: High-Accuracy Low-Power GNSS SoC with an Integrated Application Processor