Abstract:The annealing process is usually used to heat-treat cold-deformed 304 stainless steel to improve its microstructure and properties to a certain extent; however, it requires a high temperature and a long time. Because the thickness of the ultrathin strip reaches the micrometer level, it has only one or several layers of grains in the thickness direction, and the control of morphology and performance is complex. In this study, pulsed current loading was used to replace traditional annealing for treating ultrathin strips of cold-rolled 304 stainless steel. After loading a 25 W pulsed current treatment for 5 min on the cold-rolled sample, which had a thickness of 0.035 mm and width of 6 mm, complete recrystallization occurred, and the mechanical properties were significantly improved. At this point, the measured temperature was 540 °C. When annealing was used to treat the sample with the same temperature and for the same duration, the microstructure was still dominated by deformed crystals, and the mechanical properties were poor. When annealing was used to obtain a microstructure and properties similar to those obtained via 25 W electrical treatment, the required annealing temperature and time were 810 °C and 60 min, respectively. Pulsed current can increase the vacancy diffusion flux in the sample, accelerate the atomic movement, reduce the recrystallization activation energy, and make the cold-rolled 304 stainless steel ultrathin strip completely recrystallize at a lower temperature and in a shorter time. As the current power continued to increase, the recrystallized grains grew. When the pulsed current power was increased to 25 W, the recrystallized grains grew negligibly. Both recrystallization and grain growth have power thresholds. This study provides a novel approach for regulating the microstructure and mechanical properties of ultrathin cold-rolled 304 stainless steel strips.

The effect of hot- and cold-rolling on the electropulse-induced microstructure and property changes in medium carbon low alloy steels

Effects of Electric Current Pulses on Mechanical Properties and Microstructures of As-Quenched Medium Carbon Steel

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Effect of Electropulsing on Grain Refinement of a Medium Carbon Low Alloy Steel

Electropulse-induced texture elimination and texture formation in hot-rolled annealed 35CrMo steel

Static Electropulsing-Induced Microstructural Changes and Their Effect on the Ultra-Precision Machining of Cold-Rolled AZ91 Alloy

Electropulsed Steels

Effect of the electropulsing on microstructure and mechanical properties of the cold-drawing copper wire

Effect of Electroplastic Treatment on Microstructure and Texture Changes of a Cold Rolling AZ31 Strip

Effect of Electropulsing Treatment on the Mechanical Properties of Q235 Steel Strip

Effect of Hot Rolling on the Microstructure and Impact Absorbed Energy of the Strip Steel by Csp

Properties, microstructure and texture evolution of cold rolled Cu strips under electropulsing treatment

Mechanism of high-energy pulsed current-assisted rolling of 08AL carbon steel ultra-thin strip

Effect of Electropulsing on Surface Mechanical Properties and Microstructure of Aisi 304 Stainless Steel During Ultrasonic Surface Rolling Process

RETRACTED: Effect of Electroplastic Rolling on Deformability, Mechanical Property and Microstructure Evolution of Ti–6Al–4V Alloy Strip

Application of High-Density Electropulsing to Improve the Performance of Metallic Materials: Mechanisms, Microstructure and Properties

Effect of Cold Rolling Prior to Annealing on the Grain Size-Energy Losses Relationship in a Low Carbon Grain Non-Oriented Semi-Processed Electrical Steel

Effect of Pulsed Current Treatment on Microstructure and Properties of 304 Stainless Steel Ultra-Thin Strip after Rolling

Effect of Electropulsing on Recrystallization and Mechanical Properties of Silicon Steel Strips

Influence of Electropulsing Treatment on Microstructure and Mechanical Properties of Cold-Rolled Mg–9Al–1Zn Alloy Strip

Microstructure and mechanical properties of high entropy CrMnFeCoNi alloy processed by electopulsing-assisted ultrasonic surface rolling