Abstract:The HPLC and LC-MS, GC-MS and other analytical methods were used to qualitatively and quantitatively analyze the intermediates and final products of Ni/W2C catalyzed glucose hydrotreating under different process conditions. Ni-W2C was recently reported as a promising catalyst for the hydrogenolysis of cellulose or glucose to EG with the highest yield of 75%, yet this was achieved at the substrate concentration less than 1% because the concentrated substrate will lead to coking. This meant low productivity and high cost for commercial production, thus hinder this promising process from industry application. Therefore, insights into the reaction network to elucidate the coking mechanism and to optimize the process are needed. In this work, the mechanistic study on the glucose conversion, especially with the concentrated glucose substrate, over 2%Ni-30%W2C/AC was systematically carried out. The reaction parameters including temperature, initial glucose concentration and H2 pressure have been investigated and the results, in combination with the intermediate analysis by LC, LCMS and GCMS, showed that three parallel reaction pathways including retro-aldol reaction, isomerization and hydrogenation were involved in the reaction. C2 product (EG) was originated from glucose hydrogenolysis while the C3 products (1,2-PG and glycerol) were originated from fructose hydrogenolysis, and the dehydration of fructose led to 5-HMF and finally to coke in concentrated glucose conversion. Based on these understanding, the ratio of C3 products to C2, on the one hand, has been manipulated by tuning of isomerization of glucose into fructose with base additive and on the other hand, coking has been avoided by accelerating its competing reactions even at the glucose concentration of 10%(mass). More interestingly, it was indicated that glucose of low concentration favors retro-aldol reaction while the one of high concentration tends to hydrogenate.

Hydrogenation of glucose over reduced Ni/Cu/Al hydrotalcite precursors

Effects of CuO/ZnO Ratio and Preparation Conditions on Performance of CuO-ZnO Catalysts in Preparing C4～C6 Polyols through Sorbitol Hydrogenolysis

Insights into the Glucose Isomerization Mechanism of Al-hydrochar Catalyst Probed by Al-oxide Species Transformation

Preparation of highly active and hydrothermally stable nickel catalysts.

Preparation of ultrafine amorphous NiWB alloys and their activities hi glucose hydrogenation to Sorbitol

Unveiling the nature of glucose hydrogenation over Raney Ni: DFT and AIMD simulations

Hydrogenation of Glucose to Sorbitol by Using Nickel Hydroxyapatite Catalyst

Development of Ru/C Catalysts for Hydrogenation of Glucose to Sorbitol

Efficient Catalytic Hydrogenation of Glucose to Sorbitol over Metallic Nickel-Rich Nickel Borides under Mild Reaction Conditions

The Hydrogenation/dehydrogenation Activity of Supported Ni Catalysts and Their Effect on Hexitols Selectivity in Hydrolytic Hydrogenation of Cellulose

Ni-Based Hydrotalcite (HT)-Derived Cu Catalysts for Catalytic Conversion of Bioethanol to Butanol

Glucose Hydrogenation over Ni–B/SiO2 Amorphous Alloy Catalyst and the Promoting Effect of Metal Dopants

Preparation of Highly Dispersed Cu Catalysts from Hydrotalcite Precursor for the Dehydrogenation of 1,4-Butanediol

Catalytic Hydrogenolysis of Glucose into Low Carbon Glycols over Modified NiB Amorphous Alloy Catalysts

Mechanistic study on catalytic conversion of glucose into low carbon glycols over nickel promoted tungsten carbide catalyst

Effective Conversion of Cellobiose and Glucose to Sorbitol Using Non-Noble Bimetallic NiCo/HZSM-5 Catalyst

Production of C2 and C3 Polyols from D-Sorbitol over Hydrotalcite-Like Compounds Mediated Bi-Functional Ni–Mg–Al–Ox Catalysts

Glucose Hydrogenation to Sorbitol over a Skeletal Ni-P Amorphous Alloy Catalyst (raney Ni-P)

Co-precipitated Ni–Mg–Al Catalysts for Hydrogen Production by Supercritical Water Gasification of Glucose

Studies on Ni/Al2O3 Catalyst for Hydrogen Production from Ethanol Steam Reforming

Sorption-Enhanced Steam Reforming of Ethanol on a Novel K–Ni–Cu–Hydrotalcite Hybrid Material