Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

Thermal Annealing Influence on Poly(3-Hexyl-thiophene)/phenyl-c61-butyric Acid Methyl Ester-Based Solar Cells with Anionic Conjugated Polyelectrolyte As Cathode Interface Layer

Annealed Treatment Effect in Poly(3-hexylthiophene):Methanofullerene Solar Cells

Inverted All-Polymer Solar Cells Based on a Quinoxaline–thiophene/naphthalene-Diimide Polymer Blend Improved by Annealing

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Influence of thermal annealing on microstructure, energetic landscape and device performance of P3HT: PCBM-based organic solar cells

Enhancement Mechanisms of the Power Conversion Efficiency for the P3HT:PCBM Bulk Heterojunction Solar Cells with a LiF Cathode Buffer Layer Due to Thermal Annealing

Quantitative Nanoscale Monitoring the Effect of Annealing Process on the Morphology and Optical Properties of Poly(3-Hexylthiophene)/[6,6]-phenyl C61-butyric Acid Methyl Ester Thin Film Used in Photovoltaic Devices

Effect of Thermal Annealing on the Performance of Ternary Organic Photovoltaics Based on PTB7:PC71BM:F8BT

Effect of Thermal Annealing on the Efficiency of Heterojunction Photovoltaic Cells Fabricated Using Poly(3-Hexylthiophene) and Methanofullerene, [6,6]-Phenyl C61-butyric Acid Methyl Ester.

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Charge transport and extraction of PTB7:PC71BM organic solar cells: effect of film thickness and thermal-annealing

Improvement of Surface Morphology of Thin ?lms and Performance by "electrical Annealing" on Polymer Solar Cells

Interface-induced crystalline ordering and favorable morphology for efficient annealing-free poly(3-hexylthiophene): fullerene derivative solar cells.

Effects of Optical Interference and Annealing on the Performance of Poly (3-Hexylthiophene): Fullerene Based Solar Cells

Performance improvement of annealing-free P3HT : PCBM-based polymer solar cells via 3-methylthiophene additive

Study of the effect of annealing process on the performance of P3HT/PCBM photovoltaic devices using scanning-probe microscopy

Electrode Interfacial Layer Optimization of n-i-p Type Perovskite Solar Cells Based on a TiO2/Perovskite/P3HT Structure

Thermal Radiation Annealing for Overcoming Processing Temperature Limitation of Flexible Perovskite Solar Cells

High-Efficiency Polymer Photovoltaic Devices from Regioregular-Poly(3-Hexylthiophene-2,5-Diyl) and [6,6]-Phenyl-c-61-butyric Acid Methyl Ester Processed with Oleic Acid Surfactant

[6,6]-Phenyl-c61-butyric Acid 2-((2-(dimethylamino)ethyl)(methyl)amino)-ethyl Ester As an Acceptor and Cathode Interfacial Material in Polymer Solar Cells

Effect of Two-Step Annealing on the Performance of Ternary Polymer Solar Cells Based on P3ht:Pc71bm:Sq