Abstract:Joint homogenization during transition metal carbides ceramic bonding has attracted much attention as a technique to increase the service temperature and relieve the residual stress for various high-temperature applications. In this work, homogeneous joints of ZrC0.85 ceramic were obtained by diffusion bonding using single Nb and multiple Ti/Nb/Ti as the interlayer. The effect of interlayer composition, bonding temperature and holding time on the microstructure of the joints was investigated. The effect of Nb and Ti on the composition homogeneity and the formation of Kirkendall voids in the ZrC0.85 joints was also discussed. When using single Nb as the interlayer, the homogenization of the joints can be achieved at a bonding temperature of ∼1500 °C and holding for 1 h and no Kirkendall voids were observed when further increasing the bonding temperature to 1600 °C because of the good mutual solubility of NbCx and ZrCx and the relative moderate diffusion rate of Nb. However, severe Kirkendall effects were observed at a higher temperature of 1700 °C, which would deteriorate the high-temperature performance of the joints. The adoption of Ti/Nb/Ti further minished the diffusion rate difference of the interfacial elements through the formation of TiCx phase. As a result, only a few Kirkendall voids were formed at 1700 °C. Nano-hardness of the resultant homogeneous joints was comparable to that of the ZrC0.85 ceramic due to their similar composition. This study shows that active diffusion bonding based on interlayer design for homogeneous joints could pave a new way to join transition metal carbides.

Diffusion bonding of ZrB 2-SiC/Nb with in situ synthesized TiB whiskers array

Microstructure and Properties of the Diffusion Bonding Zrb2-Sic/Nb Joint

Microstructure and mechanical properties of ZrB2-SiC joints fabricated by a contact-reactive brazing technique with Ti and Ni interlayers

Microstructural Evolution and Growth/degradation Behavior of in Situ TiB Whiskers in ZrB2-SiC Joints Using Ti/Ni/Ti Filler

Interfacial Microstructure and Properties of In-situ TiB Reinforced ZrB2-SiC Joints

Microstructural evolution and growth behavior of in situ TiB whisker array in ZrB2- SiC/Ti6Al4V brazing joints

Microstructural Investigation of in Situ TiB Whiskers Array Reinforced ZrB2–SiC Joint

Diffusion bonding of ZrB2-SiC and Nb using dynamic compressed Ni foam interlayer

Dissimilar Diffusion Bonding Behaviour of Ti2AlNb Alloy and TiBw/Ti64 Composites Using the Ti Interlayer

Partial Transient Liquid Phase Diffusion Bonding of ZrC-SiC and 304 Stainless Steel by Ti/Ni Interlayer: Microstructure and Properties

Interface Homogenization Control and Microstructural Analysis of ZrC0.85 Joints Diffusion Bonded Using Nb and Ti/Nb/Ti As the Interlayer

Microstructures and mechanical property of ZrC joints diffusion bonded using Ti/Ta/Ti as the interlayer

Microstructure Evolution and Its Effect on the Mechanical Properties of the ZrC–SiC Composite Joint Diffusion Bonded with Pure Ni Foil

Interfacial Structure and Fracture Behavior of TiB Whisker-Reinforced C/SiC Composite and TiAl Joints Brazed with Ti–Ni–B Brazing Alloy

Formation Mechanism of ZrC-SiC Joint Prepared by Pulsed-Current Assisted Diffusion Bonding

Interfacial Microstructure and Joining Properties of TiAl/Ti3AlC2 Diffusion Bonded Joints Using Zr and Ni Foils As Interlayer

Diffusion bonding behaviour of Nb–Si and TiAl alloys by spark plasma sintering

Microstructure and Strength of the Tib2 Cermet/Tial Joint Diffusion Bonded with Ni Interlayer

Microstructures and Mechanical Property of ZrCx Joints Diffusion Bonded Using Ti/Ta/Ti As the Interlayer

Diffusion bonding of TiB3 cermet to TiAl intermetallic

Diffusion bonding of implantable Al2O3/Ti-13Nb-13Zr joints: Interfacial microstructure and mechanical properties