Abstract:In this study, a crack-free pyrolysis process of partially cured precursor powder compacts was developed to prepare dense silicon boron carbonitride (SiBCN) monoliths at much lower temperatures (1300 degrees C), thereby circumventing the challenges of sintering densification (> 1800 degrees C). Unlike the elastic fracture in over-cured precursors or the viscoelastic deformation in under-cured precursors, the partially cured precursor, exhibiting elastic-plastic deformation behavior, facilitates limited nanoscale pore formation in a dense structure, achieving a balance between crack-free pyrolysis and densification. Compared to SiBCN derived from the over-cured precursor (sigma = similar to 159 MPa, K-IC = 1.9 MPa center dot m(1/2), Vickers hardness (HV) = 7.8 GPa, and E = 122 GPa), the resulting SiBCN monolith exhibited significantly improved mechanical properties (sigma = similar to 304 MPa, K-IC = 3.7 MPa center dot m(1/2), HV = 10.6 GPa, and E = 161 GPa) and oxidation resistance. In addition, this study investigated the high-temperature performance of SiBCN monoliths, including crystallization and oxidation, and determined the oxidation kinetics induced by pore structure healing and the different oxidation mechanisms of Si-C-N and B-C-N clusters in the amorphous structure. Due to its unique composition and structure, the SiBCN ceramic oxide layer exhibits exceptional self-healing effects on repairing the nanoporous system in the initial stage and shows outstanding high-temperature stability during prolonged oxidation, mitigating adverse effects from bubble formation and crystallization. Due to the nanoporous structure, the oxidation rate is initially controlled by gas diffusion following a linear law before transitioning to oxide layer diffusion characterized by a parabolic law. Finally, due to different valence bond configurations, Si-C-N transforms into an amorphous SiCNO structure after phase separation, unlike the nucleation and growth of residual B-N-C.

Physical and surface characteristics of the mechanically alloyed SiBCN powder

Carbon content-dependent microstructures, surface characteristics and thermal stability of mechanical alloying derived SiBCN powders

Influence of ball milling parameters on the structure of the mechanically alloyed SiBCN powder

Fabrication and characterization of amorphous SiBCN powders

Microstructure and Thermal Stability of Amorphous SiBCNAl Powders Fabricated by Mechanical Alloying

Microstructure and thermal stabilities in various atmospheres of SiB0.5C1.5N0.5 nano-sized powders fabricated by mechanical alloying technique

Boron‐dependent Microstructural Evolution, Thermal Stability, and Crystallization of Mechanical Alloying Derived SiBCN

Microstructural Features and Properties of the Nano-Crystalline SiC/BN(C) Composite Ceramic Prepared from the Mechanically Alloyed SiBCN Powder

Microstructure and high-temperature properties of SI-B-C-N MA-powders and ceramic

Synthesis Mechanism of Amorphous Si2BC3N Powders: Structural Evolution of 2si‐bn‐3c Mixtures During Mechanical Alloying

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Microstructures and Mechanical Properties of SiBCNAl Ceramics Produced by Mechanical Alloying and Subsequent Hot Pressing

Influence of Length-Scale on Stabilization of Boron Carbide in Al-based Metal Matrix Composites During Plasma Activated Sintering

BBPPAmorphous Si-B-C-N Ceramics Fabricated by High Energy Ball Milling and Hot Pressing

Research on the Densification Process of the Mechanically-Alloyed Amorphous 2Si-B-3c-n Powder

Carbon‐content‐dependent Phase Composition, Microstructural Evolution, and Mechanical Properties of SiBCN Monoliths

Structural and microstructural characterization of SiB0.5C 1.5N0.8Al0.3 powders prepared by mechanical alloying using aluminum nitride as aluminum source

Characterization of Mo–Si–B Nanocomposite Powders Produced Using Mechanical Alloying and Powder Heat Treatment

Effect of Si/C Ratio and Their Content on the Microstructure and Properties of Si–B–C–N Ceramics Prepared by Spark Plasma Sintering Techniques

Preparation of Amorphous Si-B-C-N Powders and Nano-Sized Ceramics

Fabrication of Dense SiBCN Monolith at a Lower Temperature Andits High-Temperature Performance