Abstract:Hybrid calcium carbonate particles, synthesized III the presence of block copolymer polystyrene-b-poly(acrylic acid) (PS-b-PAA), were used to fabricate polyelectrolyte (PE) such as polylallyamine hydrochloride)/ poly(strene sulfonate sodium) (PAH/PSS) and poly (diallyldimethyl ammonium chloride)/poly (styrene sulforate sodium) (PADH/PSS) Capsules, by layer-by-layer (LbL) technique. Novel micelle-enhanced polyelectrolyte (PE capsules were thus obtained. The structure of the micelle-enhanced PE microcapsules was studied in this article. Due to the presence of a large amount of negatively charged micelles inside PE capsule interior, which were liberated from templates, the capsule wall was tightly re-constructed. Different from the wall properties of the conventional PE capsules, the wall of the micelle-enhanced PE capsules showed stability under an extensive pH range from I to 14, but the micelled enhanced capsules showed dented morphology in solutions with high NaCl concentration such as 0.5 mol/L and I mol/L. The state of the block copolymer in the capsules was investigated in dialysis bag by simulating the Solution condition of the capsule interior after the template being removed. It was found that the micelle size of the block copolymer In solution of templates dissolution was tens of nanometers after the solution was dialyzed for 24 h. With the dialysis time increasing up to at least 72 It, the block copolymer began to precipitate onto the dialysis bag from the solution The interaction between the 2-D polyelectrolyte multilayer film and micelles formed by block copolymer in templates solution was studied by UV-Vis measurements as well. It was found that PE multilayer could interact with micelles via electrostatic force. At the same time I the block copolymer remained in the capsules interior could be precipitated onto the PE multilayer via dialyzing in deionized water for a long time (pH similar to 6). A micelle-related layer was formed which was stabilized by the "bridge effect" of calcium ions. That is, the wall of the micelle-enhanced PE capsules had a bilayer structure and was formed by the polyelectrolyte multilayer and micelle-related layer. It seemed that the two layers with different properties clung to each other via electrostatic force. The formation mechanism of the bilayer structure was well illuminated oil the aforementioned studies. This is a key property of the micelle-enhanced PE capsules with which all the properties of the capsules were linked. Based on the bilayer structure of the capsules, the morphology changes of the capsules in solutions with different conditions such as high NaCl concentrations could be elucidated well. However, more direct proofs and further studies were needed to completely resolve the fine structure of the micelle-enhanced PE capsules.

Fabrication of Chitosan Single-Component Microcapsules with a Micrometer-Thick and Layered Wall Structure by Stepwise Core-Mediated Precipitation.

Fabrication and formation studies on single-walled CA/NaCS-WSC microcapsules

Preparation and Characterization of NaCS–CMC/PDMDAAC Capsules

Preparation of "micelles enhanced " polyelectrolyte capsules

Preparation of microcapsules with multi-layers structure stabilized by chitosan and sodium dodecyl sulfate

Fabrication And Properties Of Chitosan Hydrogel Filled Multilayer Microcapsules

Layered Chitosan Conduits with Controllable Inner Diameters

Synthesis of Size-Controlled Acid-Resistant Hybrid Calcium Carbonate Microparticles As Templates for Fabricating “Micelles-Enhanced” Polyelectrolyte Capsules by the LBL Technique

Preparation and Characterization of Magnetic Chitosan Microcapsules

Fabrication of Microcapsules with Special Shapes by Layer-by-layer Assembly on CaCO3 Microparticles

A Facile Pathway to Fabricate Microcapsules by in Situ Polyelectrolyte Coacervation on Poly(styrene Sulfonate)-Doped CaCO3particles

Preparation and Characterization of Biocompatible Microcapsules of Sodium Cellulose Sulfate/Chitosan by Means of Layer-by-Layer Self-Assembly

Preparation of CaCO3/chitosan three-dimensional composite material via in-situ precipitation

Preparation of CaCO_3/Chitosan Three-dimentinal Composite Material via in-situ Precipitation

Structure Studies of Micelle-Enhanced Polyelectrolyte Microcapsules

Assembly of Multilayer Microcapsules on CaCO3 Particles from Biocompatible Polysaccharides

Microfluidic Fabrication of Structure-Controlled Chitosan Microcapsules via Interfacial Cross-Linking of Droplet Templates

Shell Modulation by Tailoring Substituents in Chitosan for LbL-assembled Microcapsules

Preparation of Chitosan Bicomponent Nanofibers Filled with Hydroxyapatite Nanoparticles Via Electrospinning

Preparation and Characterization of Three Dimensions Chitosan Rods with Biomimetic Layered Structure Similar to Annual Ring

Preparation of Chitosan/Hydroxyapatite Nanocomposite with Layered Structure Via In-Situ Compositing