Abstract:Hybrid calcium carbonate particles, synthesized III the presence of block copolymer polystyrene-b-poly(acrylic acid) (PS-b-PAA), were used to fabricate polyelectrolyte (PE) such as polylallyamine hydrochloride)/ poly(strene sulfonate sodium) (PAH/PSS) and poly (diallyldimethyl ammonium chloride)/poly (styrene sulforate sodium) (PADH/PSS) Capsules, by layer-by-layer (LbL) technique. Novel micelle-enhanced polyelectrolyte (PE capsules were thus obtained. The structure of the micelle-enhanced PE microcapsules was studied in this article. Due to the presence of a large amount of negatively charged micelles inside PE capsule interior, which were liberated from templates, the capsule wall was tightly re-constructed. Different from the wall properties of the conventional PE capsules, the wall of the micelle-enhanced PE capsules showed stability under an extensive pH range from I to 14, but the micelled enhanced capsules showed dented morphology in solutions with high NaCl concentration such as 0.5 mol/L and I mol/L. The state of the block copolymer in the capsules was investigated in dialysis bag by simulating the Solution condition of the capsule interior after the template being removed. It was found that the micelle size of the block copolymer In solution of templates dissolution was tens of nanometers after the solution was dialyzed for 24 h. With the dialysis time increasing up to at least 72 It, the block copolymer began to precipitate onto the dialysis bag from the solution The interaction between the 2-D polyelectrolyte multilayer film and micelles formed by block copolymer in templates solution was studied by UV-Vis measurements as well. It was found that PE multilayer could interact with micelles via electrostatic force. At the same time I the block copolymer remained in the capsules interior could be precipitated onto the PE multilayer via dialyzing in deionized water for a long time (pH similar to 6). A micelle-related layer was formed which was stabilized by the "bridge effect" of calcium ions. That is, the wall of the micelle-enhanced PE capsules had a bilayer structure and was formed by the polyelectrolyte multilayer and micelle-related layer. It seemed that the two layers with different properties clung to each other via electrostatic force. The formation mechanism of the bilayer structure was well illuminated oil the aforementioned studies. This is a key property of the micelle-enhanced PE capsules with which all the properties of the capsules were linked. Based on the bilayer structure of the capsules, the morphology changes of the capsules in solutions with different conditions such as high NaCl concentrations could be elucidated well. However, more direct proofs and further studies were needed to completely resolve the fine structure of the micelle-enhanced PE capsules.

Synthesis of Size-Controlled Acid-Resistant Hybrid Calcium Carbonate Microparticles As Templates for Fabricating “Micelles-Enhanced” Polyelectrolyte Capsules by the LBL Technique

Preparation of "micelles enhanced " polyelectrolyte capsules

Micellization Phenomena of Amphiphilic Block Copolymers Based on Methoxy Poly(ethylene Glycol) and Either Crystalline or Amorphous Poly(caprolactone-b-lactide)

A Facile Route to Synthesize Highly Uniform Nanocapsules: Use of Amphiphilic Poly(acrylic Acid)‐block‐polystyrene RAFT Agents to Interfacially Confine Miniemulsion Polymerization

Length Control of Biodegradable Fiber-Like Micelles Via Tuning Solubility: A Self-Seeding Crystallization-Driven Self-Assembly of Poly(-caprolactone)-Containing Triblock Copolymers

Structure Studies of Micelle-Enhanced Polyelectrolyte Microcapsules

Study on the Synthesis of Spherulitic Calcium Carbonate Composite in Amphiphilic Ps-B-Paa Solution and Its Crystalline Structure

Synthesis and Characterization of Amphiphilic Centipede-Like Copolymer PS-PS-PMAA

A Study of Properties of "Micelle-Enhanced" Polyelectrolyte Capsules: Structure, Encapsulation and in Vitro Release

From the 2-Dimensional Unstable Polyelectrolyte Multilayer to the 3-Dimensional Stable Dry Polyelectrolyte Capsules

Fabrication of Microcapsules with Special Shapes by Layer-by-layer Assembly on CaCO3 Microparticles

A Novel System for Water Soluble Protein Encapsulation with High Efficiency: “micelles Enhanced” Polyelectrolyte Capsules

A Facile Pathway to Fabricate Microcapsules by in Situ Polyelectrolyte Coacervation on Poly(styrene Sulfonate)-Doped CaCO3particles

Assembly of polymeric micelles into hollow microcapsules with extraordinary stability against extreme pH conditions.

Self-Assembly of Linear Amphiphilic Pentablock Terpolymer PAAx-PS48-PEO46-PS48-PAAxin Dilute Aqueous Solution

Influence of Block Copolymer on Formation and Acid Resistant Properties of Hybrid CaCO_3 Particles

Stable Microcapsules Assembled Stepwise from Weak Polyelectrolytes Followed by Thermal Crosslinking

Aggregation-Resistant Superparamagnetic Noncovalent Hybrid Multilayer Hollow Microcapsules in High Ionic Strength Media

POLYELECTROLYTE MICROCAPSULES FABRICATED <I>VIA in situ</I> COACERVATION — THE INFLUENCE OF DOPED POLYELECTROLYTE AMOUNT IN THE TEMPLATES ON THEIR STRUCTURES AND PROPERTIES

Assembly of Multilayer Microcapsules on CaCO3 Particles from Biocompatible Polysaccharides

Micelles-Encapsulated Microcapsules for Sequential Loading of Hydrophobic and Water-Soluble Drugs