Abstract:Hybrid calcium carbonate particles, synthesized III the presence of block copolymer polystyrene-b-poly(acrylic acid) (PS-b-PAA), were used to fabricate polyelectrolyte (PE) such as polylallyamine hydrochloride)/ poly(strene sulfonate sodium) (PAH/PSS) and poly (diallyldimethyl ammonium chloride)/poly (styrene sulforate sodium) (PADH/PSS) Capsules, by layer-by-layer (LbL) technique. Novel micelle-enhanced polyelectrolyte (PE capsules were thus obtained. The structure of the micelle-enhanced PE microcapsules was studied in this article. Due to the presence of a large amount of negatively charged micelles inside PE capsule interior, which were liberated from templates, the capsule wall was tightly re-constructed. Different from the wall properties of the conventional PE capsules, the wall of the micelle-enhanced PE capsules showed stability under an extensive pH range from I to 14, but the micelled enhanced capsules showed dented morphology in solutions with high NaCl concentration such as 0.5 mol/L and I mol/L. The state of the block copolymer in the capsules was investigated in dialysis bag by simulating the Solution condition of the capsule interior after the template being removed. It was found that the micelle size of the block copolymer In solution of templates dissolution was tens of nanometers after the solution was dialyzed for 24 h. With the dialysis time increasing up to at least 72 It, the block copolymer began to precipitate onto the dialysis bag from the solution The interaction between the 2-D polyelectrolyte multilayer film and micelles formed by block copolymer in templates solution was studied by UV-Vis measurements as well. It was found that PE multilayer could interact with micelles via electrostatic force. At the same time I the block copolymer remained in the capsules interior could be precipitated onto the PE multilayer via dialyzing in deionized water for a long time (pH similar to 6). A micelle-related layer was formed which was stabilized by the "bridge effect" of calcium ions. That is, the wall of the micelle-enhanced PE capsules had a bilayer structure and was formed by the polyelectrolyte multilayer and micelle-related layer. It seemed that the two layers with different properties clung to each other via electrostatic force. The formation mechanism of the bilayer structure was well illuminated oil the aforementioned studies. This is a key property of the micelle-enhanced PE capsules with which all the properties of the capsules were linked. Based on the bilayer structure of the capsules, the morphology changes of the capsules in solutions with different conditions such as high NaCl concentrations could be elucidated well. However, more direct proofs and further studies were needed to completely resolve the fine structure of the micelle-enhanced PE capsules.

Fabrication of Microcapsules with Special Shapes by Layer-by-layer Assembly on CaCO3 Microparticles

Fabrication and formation studies on single-walled CA/NaCS-WSC microcapsules

Preparation of "micelles enhanced " polyelectrolyte capsules

Synthesis of Size-Controlled Acid-Resistant Hybrid Calcium Carbonate Microparticles As Templates for Fabricating “Micelles-Enhanced” Polyelectrolyte Capsules by the LBL Technique

Assembly of Multilayer Microcapsules on CaCO3 Particles from Biocompatible Polysaccharides

A Facile Pathway to Fabricate Microcapsules by in Situ Polyelectrolyte Coacervation on Poly(styrene Sulfonate)-Doped CaCO3particles

Fabrication of Microcapsule Arrays on Chemically Patterned Surfaces Via Covalent Linking

Single Polyelectrolyte Microcapsules Fabricated by Glutaraldehyde‐Mediated Covalent Layer‐By‐Layer Assembly

Fabrication of Diverse Microcapsule Arrays of High Density and Good Stability

Multilayer Capsules with Cell-like Topology: Fabrication and Spontaneous Loading of Various Substances in Aqueous and Ethanol Solutions

Fabrication And Properties Of Chitosan Hydrogel Filled Multilayer Microcapsules

Direct Covalent Assembly to Fabricate Microcapsules with Ultrathin Walls and High Mechanical Strength

Structure Studies of Micelle-Enhanced Polyelectrolyte Microcapsules

Preparation and Characterization of Sodium Alginate and Polyquaternium‐10 Hollow Microcapsules by a Layer‐by‐Layer Self‐Assembly Technique

From the 2-Dimensional Unstable Polyelectrolyte Multilayer to the 3-Dimensional Stable Dry Polyelectrolyte Capsules

Polyphosphazene Microcapsules Fabricated Through Covalent Assembly.

Stable Microcapsules Assembled Stepwise from Weak Polyelectrolytes Followed by Thermal Crosslinking

Layer-by-layer Assembly of Microcapsules and Their Biomedical Applications

Fabrication of Chitosan Single-Component Microcapsules with a Micrometer-Thick and Layered Wall Structure by Stepwise Core-Mediated Precipitation.

Assembly of polymeric micelles into hollow microcapsules with extraordinary stability against extreme pH conditions.

Fabrication of Hierarchical CaCO3 Mesoporous Spheres: Particle-Mediated Self-Organization Induced by Biphase Interfaces and SAMs