Abstract:Nodal joints uniting separate elements of steel structures are the most important parts of the whole structure. For the tensile zone of a connection, the study of its stress-strain state up to the limit of exhaustion of its bearing capacity is of greatest interest. There exist different design approaches to obtain the ultimate capacity of a tension-zone of a steel joint, both numerical and analytical methods. In the presented paper this has been realized using a general-purpose finite element analysis package. The application of numerical methods for modelling the tensile performance of the T-component makes it possible to compensate for the lack of data on full-scale experimental studies. Despite the widespread use of finite element analysis packages, there are still no clear guidelines for creating numerical models of such connections. Numerical analysis has taken into account important effects such as the nonlinear behavior of the material and the contact interaction of its individual elements. Finite element analyses should represent the reality in an accurate way while not being too time consuming to be set up and run. That means appropriate parameters and phenomena, such as element types or loading procedure, should be compiled in a way suitable to the problem at hand, so that the discrepancy between reality and model is sufficiently small. A FE-model with wrong representation of reality can be solved correctly with FEA, but will thereby provide inaccurate results. Therefore, one needs understanding about FE parameters and their influence on time to execute the procedure effectively. When these conditions are met, the possibility to analyze larger number of T-stubs with less user modification opens up. The analytical method for the calculation of the properties of a bolted joint established by the structural Eurocodes proposes the T-stub as a component for the characterization of the tension and compression zones in moment joints. Using the component method, which is the basis for the calculation of joints according to the EN 1993-1-8 design codes, the value of the ultimate tensile force for the T-shaped component of the dimensions adopted in the work was obtained; the obtained values of the ultimate forces were further used in the numerical experiment. Keywords: end-plate connection, numerical model, T-stub component, bolt connection.

Study on the Component-Based Model of Semi-Rigid Beam-to-column Joints Initial Stiffness

A Multi-Spring Component Modelling Approach for T-Stub Connections

Component Modeling of Steel Bolted End-Plate Joints under Bending and Shearing Loads

A Ductility-Centred Analytical Model for Axially Restrained Double-Span Steel Beam Systems Subjected to Sudden Columns Loss

Modeling of Steel Bolted T-Stub Connection under Large Deformation Condition

Experimental Study on Reduced I-beam to CFRST Column Joints under Cyclic Loading

STUDY OF THE STRESS DISTRIBUTION AND MECHANICAL PROPERTIES OF THE BEAM-COLUMN JOINT IN STEEL ROOF TRUSS BASED ON FULL-SCALE TESTS

Load-Carrying Capacity and Practical Calculation Method for Hollow Cylinder Joints Connected with H-Shaped Beams

An Axial Semi-Rigid Connection Model for Cross-Type Transverse Branch Plate-to-chs Joints

EXPERIMENTAL STUDY ON THE SEISMIC BEHAVIOR OF CFST RECTANGULAR COLUMN TO H-SECTION STEEL BEAM CONNECTIONS WITH EXTERNAL STIFFENERS

RIGIDITTY OF WELDED HOLLOW SPHERICAL JOINTS ON FINITE ELEMENT ANALYSIS PRECESION OF RETICULATED SHELLS

Research on the Semi‐rigid Joint with T‐stub in Beam‐to‐Column Connection: Suggestion for Initial Rotational Stiffness Formula

Analysis on the Initial Rotational Stiffness of End-plate Beam-to-column Composite Joint

An assessment of application of the component-based method to full range behaviour of joints between steel beam to concrete filled steel tube columns under extreme loading conditions

An Investigation of the Effect of Semi-rigid Connections on Sudden Column Removal in Steel Frames

WARPING TRANSFER THROUGH JOINTS OF RHS COLUMN AND I-BEAM

Comparative analysis of three design methods for a new type beam-column assembled rigid joint

The Effect of Joint Stiffness on Static Capability of Multistory Steel Frames

T-STUB COMPONENT BEHAVIOR OF THE BEAM TO COLUMN BOLTED FLANGE CONNECTION BASED ON A NUMERICAL ANALYSIS AND EN 1993-1-8 DESIGN CODES

Component-based model of semi-rigid connections for nonlinear analysis of composite structures

Effect of Stiffeners on Mechanical Behavior of T-Stubs Based on Experiment and Numerical Simulations