Abstract:In order to improve the performance of WC based steel bonded carbide, the effects of Ni3Al content on microstructure and properties of WC-Fe(Cr, Mo) steel bonded carbide were explored based on thermodynamic calculation. The alloys with different Ni3Al contents (0, 0.5%, 1.0%, 1.4%, mass fraction) were prepared by liquid phase sintering method through adding Al with the form of Ni3Al prealloyed powders. The liquidus temperature, phase composition and microstructure of alloys were analyzed by the differential scanning calorimetry (DSC), X-ray diffractometer (XRD), scanning electron microscope (SEM) and metalloscope, respectively. The effects of Ni3Al content on the mechanical and magnetic properties of alloys were investigated. The results show that, with the increase of Ni3Al content, γ-Fe content increase, due to the improved stabilities of austenite through the solution of Ni element. The driving force for the nucleation of the γ-binder precipitating from liquid phase at 1250 ℃ increases, which refines the grains, NiAl precipitation in the binder phase increases. The hard phases are mainly WC and Fe3W3C, with the increase of Ni3Al content, more C element dissolves in γ-Fe binder phase, which leads to a less precipitation of Fe3W3C, refined WC grains are distributed more dispersedly. Above all, with the increase of Ni3Al content, the density of alloys decreases slightly. The magnetic saturation of binder phase decreases while coercive force increases. The hardness of alloys raises while the transverse rupture strength of alloys first decreases, then increases. Both the hardness and transverse rupture strength reach maximum value when the Ni3Al content is 1.4%.

Preparation and Mechanical Properties of WC-10 Ni3Al Cemented Carbides with Plate-Like Triangular Prismatic WC Grains

High Temperature Compressive Properties and Microstructure of WC-Ni3Al Cermets Prepared by Spark Plasma Sintering

Microstructure and Properties of Ultrafine Grained AlCrFeCoNi/WC Cemented Carbides

Effect of titanium addition on microstructure and mechanical properties of WC-Ni<sub>3</sub>Al cemented carbide br

Study on High Temperature Deformation Behavior of WC-10 Wt %ni3al Cemented Carbide

Effects of Ni3Al content on microstructure and properties of WC based steel bonded carbide

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Microstructure and Mechanical Properties of WC-10wt.%AlCoCrFeNi Cemented Carbides Fabricated by Plasma-Assisted Ball Milling

Study on Microstructure and Mechanical Properties of WC-10Ni 3 Al Cemented Carbide Prepared by Different Ball-Milling Suspension.

WC-8Co-2Al (wt%) Cemented Carbides Prepared by Mechanical Milling and Spark Plasma Sintering

Fabrication of graded WC-Ni<sub>3</sub>Al cemented carbides by lamination pressing and spark plasma sintering

Preparation and Properties of WC-TiC-Ni Cemented Carbide

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Preparation of η phase powder and the effect of sintering process on the plate-like WC grain

Effects of Ni Addition and Cyclic Sintering on Microstructure and Mechanical Properties of Coarse Grained WC–10Co Cemented Carbides

In-situ Elongated Aluminium Borate Grains Toughening WC- 1.87 Wt % Al2O3- 4.13 Wt % ZrO2 Composite Via Spark Plasma Sintering

Fabrication and Mechanical Properties of Ultrafine Grained WC–10Co–0.45Cr3C2–0.25VC Alloys

Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Microstructure and Mechanical Properties of SPSed (Spark Plasma Sintered) Ti66Nb13Cu8Ni6.8Al6.2 Bulk Alloys with and without WC Addition

Effect of Bimodal WC Particle Size and Binder Composition on the Morphology of WC Grains in WC–Co–Ni3Al Cemented Carbides