Abstract:Microstructure and mechanical properties development of extruded Mg-1Y (wt. %) binary alloy during equal channel angular pressing (ECAP) with route Bc at 400 degrees C, and subsequent annealing treatment between 300-400 degrees C at different holding time of 5-120 min were investigated using an optical and scanning electron microscope (SEM), electron back scattered diffraction (EBSD), tensile test, and hardness test. The grain size of as-extruded material (similar to 10.9 mu m) was refined significantly by 1-pass ECAP (similar to 5.8 mu m), and resulted in a remarkably enhanced elongation to failure (EL) (similar to+62%) with a slightly decreased ultimate tensile strength (UTS) (similar to-3%) comparing to the as-extruded condition (EL = 11.3%, UTS = 200 MPa). The EL was further increased to 27.3% (similar to+142%) after four passes of ECAP comparing to the as-extruded condition, which was mainly caused by the much more homogenized microstructure. The split basal poles with about 60 degrees rotations to the extruded direction (ED), the relatively coarsened grain size by static recrystallization (SRX) and post-dynamic recrystallization (PDRX) after four passes of ECAP might be responsible for the decreased strength with increasing ECAP pass. During the annealing treatment, recovery dominantly occurred at 300 degrees C, SRX and grain growth emerged at 350 degrees C and 400 degrees C, respectively. Meanwhile, the grain grew and hardness decreased rapidly even within 5 min for 1-pass ECAPed material at 400 degrees C, indicating a larger grain boundary mobility of ECAPed materials induced by higher deformation energy than the as-extruded ones.

Improved Mechanical Property and Internal Friction of Pure Mg Processed by ECAP

Effect of Heat Treatment on Internal Friction in ECAP Processed Commercial Pure Mg

Internal Friction and Microplastic Deformation Behavior of Pure Magnesium Processed by Equal Channel Angular Pressing

Low-Frequency Damping Behavior of Pure Mg Processed by Equal Channel Angular Pressing

The improvement of grain refinement, texture modification and mechanical properties of pure Mg prepared by cyclic expansion extrusion with an asymmetric extrusion cavity

Microstructure and tensile property of the ECAPed pure magnesium

Ductility enhancement in Mg–8.7Gd–4.18Y–0.42Zr magnesium alloy fabricated through extrusion and equal channel angular pressing (EX-ECAP)

Mechanical Properties and Damping Behavior of Magnesium Alloys Processed by Equal Channel Angular Pressing

Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy Processed by Equal Channel Angular Pressing

Microstructure and Mechanical Property of Pure Magnesium Processed by Cyclic Extrusion Compression

Microstructure Evolution and Mechanical Behavior of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP at High Temperature

Effect of ECAP on Mechanical and Damping Properties of Mg-0.6%Zr Alloy

Damping Behavior and Mechanical Properties of Mg-Cu-Mn Alloy Processed by Equal Channel Angular Pressing

Mechanical Properties and Damping Capacities of Magnesium Alloys Processed by Equal Channel Angular Extrusion (Ecae)

Compressive Deformation of Mg–Zn–Y–Zr Alloy Processed by Equal Channel Angular Pressing

Study on the Effect of the ECAP Deformation on the Organization and Properties of the Extruded Mg-Sn-Al Alloys

Equal-Channel Angular Pressing of Magnesium Alloy Az91 and Its Effects on Microstructure and Mechanical Properties

Improvement of Strength and Ductility of Mg-Zn-Ca-Mn Alloy by Equal Channel Angular Pressing

Microstructural Evolution and Mechanical Properties of Mg95.5Y3Zn1.5 Alloy Processed by Extrusion and ECAP

Effects Of Ecap And Annealing Treatment On The Microstructure And Mechanical Properties Of Mg-1y (Wt. %) Binary Alloy

The microstructure and mechanical properties of Mg-Sn-based alloy processed by differential-thermal equal channel angular pressing