Abstract:Equal channel angular pressing (ECAP) is an efficient metal forming tool, generally used to improve the mechanical properties by refining the grain structure in metals and alloys. In the present work, both experimental and simulation approaches have been utilized to investigate the deformation behavior of EN AW 7075 alloy during ECAP. The formation and homogeneity of the Von-Mises stress and plastic strain of the samples during ECAP with different outer corner angles (OCAs) have been investigated by the finite element method (FEM). The results revealed that the effective strain was higher and uniform for 10°, 20°, and 30° OCAs die compared to other OCAs. Beyond 30°, the magnitude of strain was found lower with a less homogenous distribution of strain. A sharp plastic deformation zone (PDZ) was noticed for 10° and 20° OCAs, although broadened gradually over an OCA value of 20°. Moreover, lower and uniform Von-Mises stress was generated along the diameter of the sample for the OCA of 20° compared to other OCAs. A gradual reduction of plastic strain has been documented with the enhancement of OCAs along with the sample diameter. The sharpest damage, however, was noticed for the OCA of 90° due to the higher gap between the sample and both die surfaces. Interestingly, the most uniform severe plastic deformation and highest strain homogeneity in terms of inhomogeneity index and coefficient of variance were achieved for 20° and 30° OCAs. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analysis illustrated the formation of ultra-fine grain structures containing very fine η ́ and η precipitates during the post-ECAP process. An improvement in the hardness, yield strength, and ultimate strength by 22%, 18%, and 14%, respectively, after ECAP has been recorded in comparison to the initial artificially aged condition. The improvements in mechanical properties were improvised primarily due to grain refinement combined with precipitate hardening.

A simultaneous enhancement of both strength and ductility by a novel differential-thermal ECAP process in Mg-Sn-Zn-Zr alloy

Evading Strength-Ductility Tradeoff in Mg Alloy via Uniform Microstructure and Unique Texture Modification Induced by Moderate Temperature ECAP

The microstructure and mechanical properties of Mg-Sn-based alloy processed by differential-thermal equal channel angular pressing

Ductility enhancement in Mg–8.7Gd–4.18Y–0.42Zr magnesium alloy fabricated through extrusion and equal channel angular pressing (EX-ECAP)

Microstructural evolution and mechanical properties of AZ31 Mg alloy fabricated by a novel bifurcation-equal channel angular pressing

Study on the Effect of the ECAP Deformation on the Organization and Properties of the Extruded Mg-Sn-Al Alloys

Precipitation behaviors and mechanical properties of a solution-treated Mg-Gd-Nd-Zn-Zr alloy during equal-channel angular pressing process

Tailoring Mechanical Properties of Mg–Al–Zn–Sn–Mn Alloy by Multipass Equal Channel Angular Pressing

Effect of ECAP temperature on formation of triple heterogeneous microstructure and mechanical properties of Zn–1Cu alloy

Development of mechanical properties and microstructure for Al–Zn–Mg–Cu alloys through ECAP after optimizing the outer corner angles through FE modeling

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Improvement of ductility and work hardening ability in a high strength Zn-Mg-Y alloy via micron-sized and submicron-sized YZn12 particles

A High-Strength and Biodegradable Zn–Mg Alloy with Refined Ternary Eutectic Structure Processed by ECAP

Effect of ECAP on Mechanical and Damping Properties of Mg-0.6%Zr Alloy

Effect of rotational-die ECAP parameters on microstructure and mechanical properties of Mg97Y2Zn alloys

Effect of ECAP on the microstructure and mechanical properties of Zn-0.5Ag-0.08Mg alloy

Enhanced ductility of Mg–1Zn–0.2Zr alloy with dilute Ca addition achieved by activation of non-basal slip and twinning

Enhanced Strength–Ductility Synergy of Mg-Al-Sn-Ca Alloy via Composite Asymmetric Extrusion

Simultaneously Enhanced Mechanical Properties and Damping Capacities of ZK60 Mg Alloys Processed by Multi-Directional Forging

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

Extraordinary mechanical properties of AZ61 alloy processed by ECAP with 160° channel angle and EPT