Abstract:The concept of grain boundary engineering (GBE) has been proposed based on the fact that many studies have demonstrated that boundaries associated with low Sigma-value coincident site lattice (CSL) misorientations show higher resistance to intergranular fracture and corrosion, reduced susceptibility to impurity segregation and superior ductility. It is commonly accepted that for fcc metals of low to medium stacking fault energy metals, including Ni and many Ni-alloys, the most important CSL boundary for the GBE process is a Sigma 3 boundary, the occurrence of which is dominated by the formation of annealing twins. Moreover, it has been found that repetitive thermo-mechanical processing can be used to increase further the fraction of Sigma 3 (and Sigma 3(n) (n >1)) boundaries. However, the mechanism for this is not yet clear. Therefore, an investigation on the evolution of Sigma 3 boundaries during recrystallization is important for understanding the mechanisms of GBE for those materials. In the present paper the evolution of Sigma 3 boundaries during recrystallization in a 96% cold-rolled sample of pure nickel of 99.996% purity has been explored using orientation maps obtained using electron backscatter diffraction (EBSD). Each orientation map was taken from the same area after annealing for various times. Based on the EBSD data the Sigma 3 boundaries can be divided into two groups: "twin" type and "non-twin" type. These groups can be differentiated using a parameter of deviation angle (Delta theta) of boundary misorientation to the ideal twin misorientation (60 degrees < 111 >). During recrystallization incoherent twin boundaries are found to develop from coherent twin boundaries. It is also that most Sigma 3(n) (n >1) boundaries are formed by impringement of a nucleus with its n-order twins, and that the chance for such impingement events decreases significantly with increasing n. Most non-twin type Sigma 3 boundaries arise from impingement of Sigma 1 and twin type Sigma 3 boundaries. Non-twin type Sigma 3 boundaries may be more effective than twin type Sigma 3 boundaries to develop a beneficial grain boundary network.

Boundary Migration During Recrystallization of Heavily Deformed Pure Nickel

Investigation of Boundary Migration During Grain Growth in Fully Recrystallised High Purity Nickel

Local Boundary Migration During Recrystallization in Pure Aluminium

Advancement In Characterization And Modeling Of Boundary Migration During Recrystallization

Boundary Migration in a 3D Deformed Microstructure Inside an Opaque Sample

In-Situ Observations of Migration of Recrystallization Boundaries in Pure Aluminium

Analysis of the Growth of Individual Grains During Recrystallization in Pure Nickel

Evolution of Sigma 3 Boundaries During Recrystallization of Cold-Rolled Nickel Deformed to High Strain

Interaction Between Recrystallization and Helium Behavior in Cold-Rolled Nickel

Non-uniform Grain Boundary Migration During Static Recrystallization: A Cellular Automaton Study

Measurements of the Curvature of Protrusions/Retrusions on Migrating Recrystallization Boundaries

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

In Situ Study of the Microstructural Evolution of Nickel-Based Superalloys with High Proportional Twin Boundaries Obtained by High-Temperature Annealing

Directional recrystallisation in nickel based high temperature alloy

Determining local mobility variation along recrystallization boundaries

Recrystallization Texture in Nickel Heavily Deformed by Accumulative Roll Bonding

Implication of site-specific segregation on grain boundary structural transition and deformation response in nanocrystalline Ni-Nb alloy

Direct Observation of Nucleation in the Bulk of an Opaque Sample

Effect of recrystallization on diffusion in ultrafine grained Ni

3d Characterization Of Recrystallization Boundaries

Recovery in heavily deformed nickel during room temperature storage