Abstract:To explore room-temperature strengthening and high-temperature ductility, a lightweight novel Mg-1.85Gd-0.64Al-0.62Zn alloy was fabricated by innovative multidirectional forging and a hot-rolling technique. Microstructures and mechanical properties were studied at room and elevated temperatures with an optical microscope, an X-ray diffractometer, and a tensile tester. An ultimate tensile strength of 260 MPa, yield strength of 171 MPa, and elongation of 20.4% were demonstrated at room temperature. The room-temperature strengthening mechanisms were identified by strengthening the model estimation. A type C Portevin-Le Chatelier effect was discovered and elucidated in this alloy. X-ray diffraction analysis revealed that the phase composition is α-Mg solid solution and (Mg, Al)3Gd, Al7Zn3, and Al2Gd intermetallic compounds. Examination of the microstructure at elevated temperatures revealed that dynamic recrystallization and dynamic grain growth occur. In particular, it was discovered that bimodal microstructures or incomplete dynamic recrystallization microstructures exist in high-temperature deformation. A maximum quasi-superplasticity of 228.4% was demonstrated in this alloy at 673 K and 5.0 × 10-4 s-1. Flow stress curves showed that the present alloy exhibits Sotoudeh-Bate curves or a long intermediate strain-hardening stage followed by a strain-softening stage. A modified Zerilli-Armstrong constitutive equation incorporating the number of dislocations was established. The power-law constitutive equation was established to identify the deformation mechanism. Both constitutive models had good predictability. At 673 K and 5.0 × 10-4 s-1, the stress exponent was 4, and the average deformation activation energy was 104.42 kJ/mol. The number of dislocations inside a grain was 146. This characteristic evidence confirmed that dislocation motion controlled by pipe diffusion dominates the rate-controlling process under this condition.

Microstructure Evolution of Mg-3%Al-1%Zn Alloy Tube During Warm Bending

Deformation mechanisms in AZ31 magnesium alloy tube bending

Microstructure and bendabiltiy of AM60 and AZ61 magnesium alloy tubes

Bending Mechanisms in AM30 Alloy Tube Using a Rotary Draw Bender

Preparation of AZ31 Magnesium Alloy Thin-Walled Tubes by a New Type of Compound Extrusion by Direct Extrusion and Multi-Pass Bending

The Deformation Behavior and Microstructure Evolution of Cladding Tube during Spinning Composite Process of Mg/Al Tube

Asymmetry Strain Hardening Behavior in Mg-3%Al-1%Zn and Mg-8%Gd-3%Y Alloy Tubes

Bendability of the Wrought Magnesium Alloy AM30 Tubes Using a Rotary Draw Bender

Microstructure and Mechanical Properties of AZ80 Magnesium Alloy Tube Fabricated by Hot Flow Forming

Deformation Behavior and Microstructure Evolution of AZ31 Mg Alloy by Forging–Bending Repeated Deformation with Multi-pass Lowered Temperature

Study on Gas Bulging Forming and Contradictive Cooling Bonding of AZ31/Al7475 Bimetal Composite Tube

Room-Temperature Strengthening, Portevin-Le Chatelier Effect, High-Temperature Tensile Deformation Behavior, and Constitutive Modeling in a Lightweight Mg-Gd-Al-Zn Alloy

Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet with Bimodal Texture under Bending Deformation

Effect of Heat Treatment on Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Tube

In-situ investigation on the microstructure evolution and plasticity of two magnesium alloys during three-point bending

Research on microstructure evolution and deformation mechanisms of fine-grained Mg alloys minitube during manufacturing process

Temperature-Dependent Flow Behavior and Microstructural Evolution During Compression of As-Cast Mg-7.7Al-0.4Zn

Microstructure evolution, strengthening mechanisms and deformation behavior of high-ductility Mg−3Zn−1Y−1Mn alloy at different extrusion temperatures

Gas Blow Forming-Cold Contraction Bonding Technology of Mg/Al Bimetallic Composite Tube

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

Microstructural Evolution of Az61 Magnesium Alloy During Hot Deformation