Abstract:<p>In this study, the microstructure evolution and mechanical anisotropy of the extruded Mg-2Zn-0.4Mn-0.4Ce alloy tube during tensile loading along the extrusion direction (ED), 45° towards extrusion direction (45°ED) and transverse direction (TD) were investigated, respectively. The results showed that the initial extruded alloy tube had an obvious {0001} basal fiber texture with the symmetrical pole position deviating about 20° from the RD to ED, which resulted in mechanical anisotropy of the tensile yield stress (TYS) when tensile loading along the ED, 45°ED and TD. The deformation behavior of the alloy tube consisted of three stages. In the yield process, the deformation was dominated by prismatic<a>slip under tensile loading along the ED, while the deformation was dominated by basal<a>slip, next were prismatic<a>slip and pyramidal<c+a>slip under tensile loading both along the 45°ED and TD. In the initial stage after yielding, some extension twin (ETW) formed when tensile loading along the three direction, and the deformations were still dominated by the previous slip systems. In the later part of the deformation, the activation of prismatic<a>slip and the nucleation and expansion of ETW gradually reached saturation under tensile loading along the ED. The dominated prismatic<a>slip was gradually replaced by pyramidal<c+a>slip, and accompanied with a small content of contraction twin (CTW) and double twin (DTW), thus forming a typical texture of [0001]⊥ED. For the deformation both along the 45°ED and TD, dominated prismatic<a>slip and subdominant pyramidal<c+a>slip gradually became the main deformation mode after the saturation of basal<a>slip and ETW, and a small content of CTW and DTW also formed, thus forming the texture of [0001]∥ED-RD plane.</a></c+a></a></c+a></a></a></c+a></a></a></a></p>

Asymmetry Strain Hardening Behavior in Mg-3%Al-1%Zn and Mg-8%Gd-3%Y Alloy Tubes

Tension-compression Asymmetry of Extruded Mg-Gd-Y-Zr Alloy with a Bimodal Microstructure Studied by In-Situ Synchrotron Diffraction

Asymmetric Tension-Compression Mechanical Behaviors of Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy with Double-Peak Fiber Texture

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Asymmetric Tension-Compression Mechanical Behavior of the As-Cast Mg-4.58Zn-2.6Gd-0.16Zr Alloy

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation

The microstructure evolution and abnormal yield asymmetry of extruded Mg-10Gd-0.5Zr alloy

Effects of Gd Concentration on Microstructure, Texture and Tensile Properties of Mg–Zn–Gd Alloys Subjected to Large Strain Hot Rolling

Hot Deformation and Work Hardening Behavior of an Extruded Mg–Zn–Mn–Y Alloy

Cyclic Shear Deformation and Fatigue of Extruded Mg-Gd-Y Magnesium Alloy

Formation of Gradient Microstructure and Elimination of Tension-Compression Yield Asymmetry of the Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy Via Free-End Torsion

Microstructures and Tensile Properties of Mg-6Gd-3Y-1.4Zn-0.4Zr Alloys

Effects of extrusion ratio and subsequent heat treatment on the tension-compression yield asymmetry of Mg-4.58Zn-2.6Gd-0.18Zr alloys

The Role of Bimodal-Grained Structure in Strengthening Tensile Strength and Decreasing Yield Asymmetry of Mg-Gd-Zn-Zr Alloys

Towards High Ductility in Magnesium Alloys - the Role of Intergranular Deformation

Tension-Compression Asymmetric Twinning Behavior in a Cast Mg-Gd-Y-Zr Alloy

Strain Hardening Behavior of Mg–Y Alloys after Extrusion Process

The microstructure evolution and mechanical anisotropy of extruded Mg-2Zn-0.4Ce-0.4Mn alloy tube during tension in different directions

A Study of High Ductility Mg-2Gd-0.4Zr Magnesium Alloy under Monotonic Tension at Room Temperature

Effect of Effective Strain Gradient on Texture and Mechanical Properties of Mg–3Al–1Zn Alloy Sheets Produced by Asymmetric Extrusion

Hot compression behavior and microstructure evolution of Mg-Gd-Y-Zn-Zr alloy