Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Effect of Sintering Temperatures on the Reaction-Bonded Si3n4/Sic Composite Ceramics

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

Microstructures and Mechanical Properties of Pressureless Sintered Ca-3(PO4)(2)/Si3N4 Composite Ceramics

Effects of Two-Step Sintering on Performance of SiC/SiB6 Composite Ceramics

Preparation And Properties Of Sintering-Free Low Density Si3n4/Sic Composite Refractory

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Effect of temperature on the structure and mechanical properties of SiC–TiB2 composite ceramics by solid-phase spark plasma sintering

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

The Effect of Tio2 and Zro2 Additives on the Density, Microstructure, and Mechanical Properties of Pressureless Sintered Sic-B4c

Pressureless Sintering and High-Temperature Strength of SiC-AlN Ceramics

Study on the Performance for Silicon Carbide Ceramics by Hot-pressing Sintering

Effect of Silicon Addition on Mechanical Properties of Mullite-Sic Composite Refractories

Effect of Sintering Temperature on Properties of Porous SiC Ceramics Produced Through Coat-mix/Composite Additives Process

PRESSURELESS SINTERING OF SILICON CARBIDE NANOCOMPOSITE CERAMICS

Effects of Sintering Additive and Β-Si3n4 Phase Contents on the Properties of Porous Si3N4 Ceramics

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Effects Of Carbon Addition On Densification And Mechanical Properties Of Porous Si3n4 Ceramics

Effect of Sintering Additive Composition on Microstructure and Mechanical Properties of Silicon Nitride

The effect of sintering aids on microstructure and mechanical properties of HfB2-SiC composites

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene