Abstract:Abstract Powder bed fusion (PBF) is an additive manufacturing (AM) technique that holds a great promise for alumina ceramic materials to be processed in a one step. To ensure an effective outcome, the powder material should be thoroughly tailored, and the process parameters should be appropriately investigated. These process parameters include laser power, scanning speed, hatching space, and scanning strategies. The alumina powder has been tailored and modified to be appropriately used for PBF using the spray-drying technique, and the process parameters have been predicted and selected using a developed numerical model. Different scanning speeds of 100, 200, 300, and 400 mm/s have been considered, and the other parameters have been numerically predicted. The results demonstrated that spray drying is an effective technique for tailoring the characteristics of alumina powder, such as particle shape, particle size distribution, flowability, and absorptivity, making it ideally suited for PBF processing. Furthermore, the developed numerical model demonstrated outstanding reliability in predicting the most effective laser power and hatching space for different scanning speeds, resulting in significant cost and time savings when compared to relying solely on experimental trials. Employing a scanning speed of 400 mm/s yielded a significant improvement in relative density and quality of the printed samples surpassing other scanning speeds. Moreover, this speed effectively addressed various challenges encountered by other scanning speeds. Following the optimization of process parameters, it was determined that a relative density of 94.5% could be achieved by utilizing a scanning speed of 400 mm/s, a laser power of 210 W, and a hatching space of 30 μm. However, the evaluation of mechanical performance revealed that while the microhardness of the printed alumina samples matched the values reported in the literature, the attained compressive strength fell significantly below the values reported in the literature.

Hydrothermal treatment of alumina powders to alter the low-temperature binding of chemically bonded phosphate ceramic composites via infrared irradiation

Infrared Irradiation to Drive Phosphate Condensation as a Route to Direct Additive Manufacturing of Oxide Ceramics

Hydration of high alumina cement–silica fume composite with addition of Portland cement or sodium polyphosphate under hydrothermal treatment

Enhancing powder bed fusion of alumina ceramic material: a comprehensive study from powder tailoring to mechanical performance evaluation

Examination of patterns in obtaining porous structures from submicron aluminum oxide powder and its mixtures

Effect of particle size distribution and printing parameters on alumina ceramics prepared by Additive Manufacturing

In situ high-temperature X-ray diffraction, FT-IR and thermal analysis studies of the reaction between natural hydroxyapatite and aluminum powder

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

3D printing of high solid Al2O3 ceramics based on green and renewable photosensitive resin with low viscosity and low shrinkage

3D gel printing of alumina ceramics followed by efficient multi-step liquid desiccant drying

Direct ink writing of aluminum-phosphate-bonded Al2O3 ceramic with ultra-low dimensional shrinkage

Influence of heat treatment on the structure and properties of ceramic heat-insulating composites based on phosphate bound expanded perlite-expanded clay

Fabrication and properties of alumina ceramics shaped by digital light processing as an additive manufacturing technology

Hydrophobic coagulation of alumina slurries

Effect of P/Al ratio on an acid aluminum phosphate solution: Thermal evolution and hygroscopic behavior

Synthesis of Preceramic Precursor Based on Organic Aluminum Salts for Stereolithographic 3D Printing of Corundum Ceramics

Fabrication of alumina ceramics with high flexural strength using stereolithography

Optimizing AlN hydrolysis process to fabricate coated modified powders for improving the properties of Si 3 N 4 /SiAlON ceramics prepared by Vat Photopolymerization

A novel composite binder design for direct ink writing alumina-based ceramics with enhanced strength at low sintering temperature

Synthesis of chemically bonded phosphate ceramic coatings with tailored curing behaviour and enhanced oxidation resistance

The hydrolysis process of γ-AlON powder and preparation of highly transparent ceramics with aqueous gel-casting