Abstract:The ability to undercool and solidification mechanism of liquid quinary Ni40Zr28.5Ti16.5Al10Cu5 alloy are investigated by electromagnetic levitation (EML) and drop tube (DT) technique. Under the EML condition, the maximum undercooling of levitated alloy can reach up to 290 K (0.21TL). Under the DT condition, the alloy achieves higher undercooling than EML, and solidifies finally into metallic glass. At lower undercooling, the solidification structure of the alloy is composed of primary Ni3Ti phase, secondary Ni10Zr7 phase and eutectic (Ni10Zr7+Ni21Zr8) phase. With the rise of undercooling, the solidification structure displays the following evolution events: phase morphology refinement, primary phase inhibition, phase number reduction, and amorphous phase formation. By using the high-speed cinematography technique, three nucleation modes are distinctly observed on the levitated alloy melt surface at the beginning of solidification, that is, single-point nucleation, multi-point nucleation and annular nucleation. The levitation state corresponding to single-point mode nucleation is relatively stable, and the alloy undercooling is also relatively low. The annular nucleation only occursin the case with high rotation speed, and the undercooling is greater than 208 K. The discrepancy between nucleation modes is due to the He gas flow for forced cooling. The theoretical calculations indicate that the alloy droplets achieve high undercoolingand large cooling rate under the DT condition. The experimental results show that when the droplet diameter decreases to 498 μm, the amorphous phase begins to appear in the alloy particles. It is noteworthy that the amorphous phase is preferentially formed inside the droplet, but not on the outer surface. The morphology of solidification structure reveals that different regions of the droplet have various local undercoolings, which result in the distribution characteristics of amorphous phase. The volume fraction of amorphous phase increases linearly with the decrease of particle diameter. When the droplet diameter decreases to 275 μm, the alloy droplets are completely frozen into glassy particles. The average eutecticspacing values are also measured at different alloy undercoolings. Compared with the classical binary eutectic growth model, the experimental eutectic growth law exhibits a large deviation in index. This indicates that the eutectic growth in multicomponent alloys displays more complex kinetic characteristics.

The Rapid Solidification of Ti-3 : Al A Molecular Dynamics Study

Rapid Solidification Mechanism of Liquid Quinary Ni-Zr-Ti-Al- Cu Alloy Investigated by High-Speed Cinematography

Molecular Dynamics Simulation of Nanocrystal Formation and Deformation Behavior of Ti3al Alloy

Structural Evolution of TiAl During Rapid Solidification Processing Revealed by Molecular Dynamics Simulations

The Development of Microstructure of Ni 3 Al During Rapid Cooling and Heating

Evolution of Icosahedral Clusters During the Rapid Solidification of Liquid TiAl Alloy

Combined Effects of High Undercooling and Large Cooling Rate on the Microstructure Evolution and Hardening Mechanism of Rapidly Solidified Ti-Al Alloys

Molecular Dynamic Simulation of Nanocrystal Formation and Tensile Deformation of TiAl Alloy

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

Microscopic Hardness and Dynamic Mechanical Analysis of Rapidly Solidified Fe-based Amorphous Alloys

Molecular Dynamics Simulation for Solidification Process of Ni-Al Alloys

Analysis of Grain Size and Five-Fold Twins During Rapid Solidification Processes Inti3al Alloy.

Primary Dendrite Growth Kinetics and Rapid Solidification Mechanism of Highly Undercooled Ti-Al Alloys

The Effect of Cooling Rate on the Microstructure Change During Rapid Solidification of Liquid Ti3Al Alloy

Dendrite Growth and Micromechanical Properties of Rapidly Solidified Ternary Ni-Fe-Ti Alloy

Rapid Solidification of Ti-6Al-4V Alloy Micro-Droplets Under Free Fall Condition

Molecular dynamics simulation studies of structural and dynamical properties of rapidly quenched Al

Elucidating Interfacial Dynamics of Ti-Al Systems Using Molecular Dynamics Simulation and Markov State Modeling

The Royal Society of C ic simulation of nanocrystal formation and tensile deformation of TiAl alloy

Growth of Icosahedral Medium-Range Order in Liquid Tial Alloy During Rapid Solidification

Metastable liquid properties and rapid crystal growth of Ti-Ni-Al alloy investigated by electrostatic levitation and molecular dynamics simulation