Abstract:The ability to undercool and solidification mechanism of liquid quinary Ni40Zr28.5Ti16.5Al10Cu5 alloy are investigated by electromagnetic levitation (EML) and drop tube (DT) technique. Under the EML condition, the maximum undercooling of levitated alloy can reach up to 290 K (0.21TL). Under the DT condition, the alloy achieves higher undercooling than EML, and solidifies finally into metallic glass. At lower undercooling, the solidification structure of the alloy is composed of primary Ni3Ti phase, secondary Ni10Zr7 phase and eutectic (Ni10Zr7+Ni21Zr8) phase. With the rise of undercooling, the solidification structure displays the following evolution events: phase morphology refinement, primary phase inhibition, phase number reduction, and amorphous phase formation. By using the high-speed cinematography technique, three nucleation modes are distinctly observed on the levitated alloy melt surface at the beginning of solidification, that is, single-point nucleation, multi-point nucleation and annular nucleation. The levitation state corresponding to single-point mode nucleation is relatively stable, and the alloy undercooling is also relatively low. The annular nucleation only occursin the case with high rotation speed, and the undercooling is greater than 208 K. The discrepancy between nucleation modes is due to the He gas flow for forced cooling. The theoretical calculations indicate that the alloy droplets achieve high undercoolingand large cooling rate under the DT condition. The experimental results show that when the droplet diameter decreases to 498 μm, the amorphous phase begins to appear in the alloy particles. It is noteworthy that the amorphous phase is preferentially formed inside the droplet, but not on the outer surface. The morphology of solidification structure reveals that different regions of the droplet have various local undercoolings, which result in the distribution characteristics of amorphous phase. The volume fraction of amorphous phase increases linearly with the decrease of particle diameter. When the droplet diameter decreases to 275 μm, the alloy droplets are completely frozen into glassy particles. The average eutecticspacing values are also measured at different alloy undercoolings. Compared with the classical binary eutectic growth model, the experimental eutectic growth law exhibits a large deviation in index. This indicates that the eutectic growth in multicomponent alloys displays more complex kinetic characteristics.

Molecular Dynamics Simulation for Solidification Process of Ni-Al Alloys

The Development of Microstructure of Ni 3 Al During Rapid Cooling and Heating

Influences of Solution Cooling Rate on Microstructural Evolution of a Multiphase Ni3Al-based Intermetallic Alloy

The Effect of Cooling Rate on the Microstructure Change During Rapid Solidification of Liquid Ti3Al Alloy

Structural Simulation of Clusters in Liquid Ni-Al Alloy

Solidification Behavior of Ni-based Superalloy at Different Cooling Rates

Thermal Expansion of Ni3al Intermetallic Compound: Experiment and Simulation

Effects of Cooling Rate on the Solidification Process of Pure Metal Al: Molecular Dynamics Simulations Based on the MFPT Method

Rapid Solidification Mechanism of Liquid Quinary Ni-Zr-Ti-Al- Cu Alloy Investigated by High-Speed Cinematography

Microstructural Feature and Evolution of Rapidly Solidified Ni 3 Al-Based Superalloys

Numerical Simulation of Recalescence of 3-Dimensional Isothermal Solidification for Binary Alloy Using Phase-Field Approach

Microscopic Structure Evolution and Amorphous Solidification Mechanism of Liquid Quinary Zr<sub>57</sub>Cu<sub>20</sub>Al<sub>10</sub>Ni<sub>8</sub>Ti<sub>5</sub> Alloy

Density Measurement and Atomic Structure Simulation of Metastable Liquid Ti-Ni Alloys

Simulation Study of Effects of Cooling Rate on Microstructure of Liquid Metal Na During Solidification Processes

Atomic-Scale Computer Simulation for Ternary Alloy Ni-Cr-Al During Early Precipitation Process

Atomic-scale Computer Simulation for Early Precipitation Process of Ni75AlxV75-x Alloys with Lower Al Concentration

Solidification of Al3Ni Peritectic Alloy at Different Cooling Velocity

Ab Initio Molecular Dynamics Simulation Of Structures Of Nial3 Alloys In Liquid And Amorphous Phase

The Rapid Solidification of Ti-3 : Al A Molecular Dynamics Study

Numerical simulation on directional solidification of Al-Ni-Co alloy based on FEM

First-principle molecular dynamics study of the structural and electronic properties of liquid and amorphous Ni–Al alloys