Effect of Oxidation Treatment on Surface Fractal Dimension of Activated Carbon Fiber

ZH Huang,FY Kang,JB Yang,KM Liang,H Zhao,BZ Dong

DOI: https://doi.org/10.1246/cl.2002.76

2002-01-01

Chemistry Letters

Abstract:Viscose rayon based activated carbon fibers (ACFs) were oxidized in different ways, resulting in changes of surface fractal dimension, which might be found in ACFs with low and high specific surface areas treated under the same condition.

What problem does this paper attempt to address?

Study on modification of carbon fiber and performance of carbon paper as gas diffusion layer

Zhijun HU,Jiang LIN,Yan ZHANG,Guilin HU

DOI: https://doi.org/10.3969/j.issn.1001-9731.2016.09.021

2016-01-01

Abstract:The effects of oxidation-coupling modification on carbon fiber(CF)were investigated according surface morphology,charge characteristics,dispersion and the conductivity of paper.At the same time,the permeabili-ty and pore size distribution of carbon paper were discussed by the ratio of CF,CF length and the loading of car-bon black.The pre-oxidation treatment of KClO3-H2 SO4 produces an etching effect on the fiber surface,gener-ates potholes in crystal defect parts,and forms axial grooves.Coupling agent KH-550 attaches on the groove in particulate,the obvious increase of absolute value of zeta was observed,electrostatic repulsion between the CFs was strengthened,the dispersion of CFs was improved,and the electrical conductivity of the carbon paper had also been improved.The length of CF and the loading of carbon black can effectively adj ust the permeability and pore size distribution of carbon paper.
Research on Surface Treatment of Carbon Fiber and the Conductive Properties of Paper

Zhijun Hu

DOI: https://doi.org/10.4028/www.scientific.net/amr.424-425.1007

2012-01-01

Abstract:The influences of the oxidative modification, coupling treatment and dispersing agent for carbon fiber dispersion and binding properties were investigated, and the relationships of different ratio of carbon fiber with the physical strength and electrical conductivity of the paper were analyzed. Meanwhile fiber surface morphology, zeta potential and absorbance slurry were tested. The result showed that: coupling modification significantly improved the dispersion performance of carbon fiber, superior than oxidative modification, the increase of the dispersion would enhance the conductivity of carbon fiber network, the effect of CPAM was best in four kinds of surface-active agent, and 30% content of carbon fiber achieved the "percolation threshold" of conductive material.
Chemical Treatment of Carbon Fibers and the Development of Functional Paper

WANG Song-ling,HU Zhi-jun,Lin Jiang

DOI: https://doi.org/10.3969/j.issn.1005-2895.2010.05.025

2010-01-01

Abstract:The influences of the chemical agents,oxidative modification and coupling treatment for carbon fiber dispersion and binding properties were investigated.The fiber suface morphology was analyzed by the image of fiber analyzer,and the fiber dispersion was reflected by the Zeta potential of slurry,absorbency and digital pictures.The functional paper were prepared with a different ratio of carbon fiber and pulp,and the physical strength and volume resistivity of the paper were tested.The results showed that: the effect of tween-80 was the best in four kinds of chemial agents,coupling modification significantly improved the dispersion performance of carbon fiber,superior than oxidative modification,the increase of the dispersion would enhance the conductivity and physical strength of functional paper,and 30% content of carbon fiber achieved the "percolation threshold" of conductive material.
The investigation on microstructure change of activated carbon fiber by oxidation

Huang Zhenghong

2004-01-01

Abstract:The activated carbon fiber (ACF) was oxidized by three kinds of meth ods,the microstructure change of activated carbon fibers were characterized by X-ray diffraction and nitrogen adsorption.The results showed that d002,La,Lc,sur face and micropore of the activated carbon fiber reduce,but mesopore of the acti vated carbon fiber increase after oxidation.
The Effect of Oxidation Treatment by KClO3/H2SO4 System on Intersurface Performance of Carbon Fibers

Linghui Meng,Dapeng Fan,Chunhua Zhang,Zaixing Jiang,Yudong Huang

DOI: https://doi.org/10.1016/j.apsusc.2012.12.066

IF: 6.7

2013-01-01

Applied Surface Science

Abstract:The polyacrylonitrile-based (PAN-based) carbon fibers with progressive amounts of the oxidation treatment have been investigated using a number of surface analytical methods. The chemical content and structure of oxidated fibers have been interrogated by X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM), then compared to the untreated ones. The value of oxygen content increased from 4.71% to 18.84%, meanwhile, the grooves on the surfaces of the carbon fibers were deepened gradually after treatments. The results of dynamic contact angle (DCA) measurements suggest that the increase in carbon fiber surface tension is mainly because of the polar component of surface tension. After treated with increasing amounts of oxidants, the monofilament tensile strength decreased less than 3.1%.
Surface modification of carbon fibers by anodic oxidation

Liang Jie-ying

Abstract:The surface of polyacrylonitrile (PAN)-based carbon fibers (CFs)was modified by anodic oxidation and characterized by atomic force microscopy, X-ray photoelectron spectroscopy, scanning electron microscopy and dynamic mechanical thermal analysis. It was found that the roughness and specific surface area of the carbon fibers were increased after oxidation treatment. The contents of hydroxyl and carbonyl groups of the treated PAN-CFs were higher than those of the untreated ones. The loss tangent peak value (tanδ_ max ) of the treated carbon fiber reinforced epoxy resin composites (CFRP) declined compared with the untreated ones, and the glass transition temperature of the epoxy resin was increased. The interlaminar shear strength (ILSS) of the CFRP can be increased by 25% under an appropriate oxidative treatment,and the loss of tensile strength was only 5%. The interfacial adhesion parameters A and α were quantitatively evaluated, and their values were consistent with the results of ILSS of CFRP.

Materials Science
Adsorption Of Volatile Organic Compounds In Nitrogen Streams On Oxidized Activated Carbon Fibres

Fy Kang,Zh Huang,Km Liang,Jb Yang,H Wu

DOI: https://doi.org/10.1260/0263617011494286

2001-01-01

Adsorption Science & Technology

Abstract:Viscose rayon-based activated carbon fibres (ACFs) with low and high specific surface areas were treated with conc. HNO3, 30 wt% H2O2 and air at different temperatures. The pore textures and surface chemistries of the samples were characterized by nitrogen adsorption at 77 K and X-ray photoelectron spectroscopic (XPS) methods. The adsorption of traces of volatile organic compounds (VOCs), i.e. benzene and methyl ethyl ketone (MEK), in nitrogen streams on the samples wwa measured by a gravimetric method. The results showed that the surface oxygen complexes and pore textures of all the oxidized ACFs were modified and differed depending on whether oxidation had been conducted under gaseous or solution conditions. ACFs with different specific surface areas possessed different adsorption characteristics towards VOC vapours after subjection to oxidation treatment.
Research on Surface Properties of Modified Activated Carbon Fiber and Its Mercury Adsorption Performance

Jianli REN,Sujuan YE,Junjie CHEN,Chuanjuan PING,Jinsong ZHOU

2010-01-01

Abstract:Three different specific surface area viscose-ACF (defined as ACF-1、ACF-2 and ACF-3) were chosen in the tests. The resulting materials ACF-N and ACF-NH3 were obtained after the sample ACF-1 was treated with HNO3 acid digestion and ammonia solution. Then the characterization of surface properties and Hg adsorption tests were conducted for these five kinds of ACFs. The nitrogen adsorption test at temperature 77.4K showed that micro-pore distribution (d2nm) of five samples existed differences. Micro-pore volume of ACF-N and ACF-NH3 samples were smaller than that of ACF-1. Surface micro-structure was analyzed by X-ray photoelectron spectroscopy (XPS). The results showed that oxygen functional groups such as carbonyl and carboxyl in ACF-N and nitrogen-containing functional groups in ACF-NH3 are significantly more than that in ACF-1. Microcrystalline structure was analyzed by X-ray diffraction (XRD) technique. It was found that graphitization and crystal level of ACF-2 and ACF-3 also increased comparing with ACF-1. Mercury removal tests revealed that mercury adsorption capacity does not simply depend on micro-pore volume because of the effect of surface micro-structure. Increasing the content of oxygen and nitrogen-containing functional groups,to some extent,can enhance mercury removal performance of ACF.
THE RESEARCH ON TRACTAL OF ACTIATED CARBON FIBER BY NITROGEN ADSORPTION

HUANG Zheng-hong,KANG Fei-yu,LIANG Kai-ming,ZHAO Hong-yang,MA Lan

DOI: https://doi.org/10.3969/j.issn.1001-3741.2000.04.011

2000-01-01

Abstract:Nitrogen adsorption(77 K) was measured on three kinds of viscose rayon based activated carbon fibers(ACFs) with different specific areas. Pore structure parameters, such as specific surface area, micropore volume and pore size distributions, were characterized. The fractal dimensions were examined by isotherm data. The results show that the fractal dimensions determined at early stage of the multilayer formation are different from those estimated at higher coverage, however, the trends are consistent and the former is more reasonable. The fractal dimensions, which reveal the content of ultramicropore, coincide with H－ K pore size distributions and characteristic adsorption energy other than specific areas and micropore volume.
Study on adsorption performance of polyacrylonitrile-based activated carbon fiber for trace of hexavalent chromium

Li Shanping,Wang Jun,Li Chong,Cui Jiangjie,Fang Hongchen

DOI: https://doi.org/10.3969/j.issn.1002-4956.2011.04.009

2011-01-01

Abstract:As an adsorbent,the polyacrylonitrile-based activated carbon fiber(PAN-ACF)was modified by air thermal oxidation,nitrate impregnation and hydrogen peroxide impregnation,respectively.The modification of PAN-ACF samples was characterized,including SEM surface morphology,BET specific surface,FTIR surface groups and total surface acidic groups.The adsorption effects on trace of hexavalent chromium and the adsorption capacity of modified PAN-ACF were studied.After modification macerated by hydrogen peroxide,the carbon crystallite size of ACF3 became smaller,causing the structure disordered,ascending the surface greatly,but the growth of surface oxygen pipeline groups was not obvious.The adsorption effect on hexavalent chromium of slightly polluted water was best,and the equilibrium temperature equation could be described with Langmuir isotherms equation,which is fit for Freundlich equation better.
Comparison of Activated Carbon from Water Bamboo Residues with Surfaces Modified by Different Methods

Da Cheng Huang,Tong Xiang Fan,Di Zhang

DOI: https://doi.org/10.4028/www.scientific.net/KEM.351.220

2007-01-01

Key Engineering Materials

Abstract:Surface modification of activated carbon was performed using such chemical methods as nitric acid and H2O2.Oxidation of the ACs made samples with weakly acidic functional groups and the presence of other groups was confirmed by Fourier transform infra red (FTIR) spectroscopy. With different time for modification, the amount of elements of carbon and oxygen will change a lot and the results of these experiments show a stronger ability of HNO3 solution in oxidization. Furthermore the differences of face morphology between ACs and oxidized ACs can be observed clearly.
Study on Carbon Fiber Surface Treatment Based on Surface Oxidation Method

Jipeng Zhang,Hui Tang,Shanshan Hao

DOI: https://doi.org/10.1109/ifost.2012.6357552

2012-01-01

Abstract:Surface conditions of carbon fibers severely effect on the bonding strength between the fibers and the matrix, even on the mechanical properties of the composites when carbon fibers were used as reinforcement on the preparation of ceramic matrix composites. Surface treatment of carbon fibers was carried out based on the air oxidation method and the liquid oxidation method with concentrated nitric acid (68%) as the oxidizing solution. It could remove impurities from the surface of carbon fibers and increase the degree of the surface concavoconvex, so the active surface area were increased and then improved the bonding strength between fibers and matrix. The surface topographies of carbon fibers after surface oxidation were characterized by SEM. The results illustrate that, impurities on the surface of carbon fibers are decreased and there are many longitudinal grooves evenly distributed on the surface in favor of increasing the bonding strength between the fibers and matrix.
The Effect of Oxidation Treatment with Supercritical Water/Hydrogen Peroxide System on Intersurface Performance for Polyacrylonitrile-Based Carbon Fibers

Linghui Meng,Dapeng Fan,Chunhua Zhang,Zaixing Jiang,Yudong Huang

DOI: https://doi.org/10.1016/j.apsusc.2013.02.007

IF: 6.7

2013-01-01

Applied Surface Science

Abstract:In order to improve the interfacial properties between carbon fibers and epoxy matrix, supercritical water and hydrogen peroxide were used as oxidation medium for the oxidation treatment for carbon fibers. Analysis results of X-ray photoelectron spectroscopy suggest that the oxygen content on the carbon fibers’ surfaces increases by these oxidation treatments. Scanning electron microscope and atomic force microscopy images indicate that the surface appearance of oxidized carbon fibers obviously changed. The maximal interlaminar shear strength and interface shear strength of carbon fiber/epoxy resin composite in which the fibers were treated by the supercritical water and hydrogen peroxide systems reaches 70.46MPa and 106.66MPa, increases by 13.4% and 29.6% respectively compared with untreated carbon fibers.
Influence of Fibre Surface Oxidation Treatment on Mechanical Interfacial Properties of Carbon Fibre/ Polyarylacetylene Composites

HJ Fu,YD Huang,L Liu

DOI: https://doi.org/10.1179/026708304225022188

IF: 1.8

2004-01-01

Materials Science and Technology

Abstract:In the present work, the mechanical interfacial properties of carbon fibre (CF) reinforced polyarylacetylene (PAA) resin composites were modified through the surface oxidation treatment of carbon fibres by ozone. Both X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) spectroscopy showed that oxidation treatment could increase the amount of elemental oxygen on the fibre surface markedly by introducing more oxygen groups. Atomic force microscopy (AFM) images indicated that weak surface regions of fibres had been etched and removed, and the degree of fibre surface roughness was increased. The interlaminar shear strength (ILSS) and the interfacial shear strength (IFSS) of CF/PAA composites were both improved notably (no less than 50%). It could be concluded that an improvement of fibre surface chemical activity, better wettability of resin on the carbon fibre surface, and stronger mechanical joining between fibres and resin all resulted in the modification of interfacial properties of carbon fibre reinforced PAA composites. The influences of temperature, ozone concentration, and treatment time on the oxidation results were studied, and optimal treatment parameters determined.
The oxidation of carbon fiber on the interlaminar shear strength and tribological properties of high-density polyethylene composites

gang tang,zhaoliang zang,wanjuan huang,jiahui huang,dongmei wang,gaofeng wei,weijian mi

DOI: https://doi.org/10.1177/0892705712452748

IF: 3.0272

2014-01-01

Journal of Thermoplastic Composite Materials

Abstract:The objective of this work is to improve the interlaminar shear strength and tribological properties of the high-density polyethylene (HDPE) composites by oxidation treatment method of carbon fiber (CF) and ultraviolet irradiation of HDPE. The morphologies of untreated and treated CFs were characterized by x-ray photoelectron spectroscopy. Surface analysis showed that after treatment, the surface of CFs chemisorbed oxygen-containing groups, active carbon atom, the surface roughness, and wetting ability were increased. The results show that the treated CF composites can possess excellent interfacial properties and tribological properties accordingly after treatment.
Experimental and Modeled Results Describing Adsorption of Trace VOCs Onto Oxidized ACF

黄正宏,康飞宇,梁开明,杨骏兵

DOI: https://doi.org/10.3321/j.issn:1000-0054.2002.10.005

2002-01-01

Abstract:Volatile organic compounds (VOC) are common airborne pollutants that endanger human health. The present work analyzed the adsorption of low concentration volatile organic compounds such as nonpolar benzene and polar methy ethyl ketone onto oxidized viscose rayon based activated carbon fibers (ACF). The Freundlich equation and the Dubinin Radushkevich (DR) equation were used to fit the measured adsorption isotherms. The results show that oxidation treatment increases the surface oxygen amount and modifies the ACF pore structure, resulting in different adsorption characteristics for the VOC. The model results agree with the measured data.
Surface Oxidation of Activated Electrospun Carbon Nanofibers and Their Adsorption Performance for Benzene, Butanone and Ethanol

Yu Bai,Zheng-Hong Huang,Feiyu Kang

DOI: https://doi.org/10.1016/j.colsurfa.2013.10.057

2014-01-01

Abstract:Carbone nanofibers prepared by electrospinning and subsequent steam activation were oxidized by treatment in HNO3 and HNO3/H2SO4 mixture. Surface morphology and degree of graphitic structure of oxidized nanofibers are affected mildly by acid oxidation according to SEM and Raman measurement. Nitrogen adsorption/desorption isotherms demonstrate decrease in specific surface area and pore volume of carbon nanofibers after oxidation. XPS spectra exhibit that oxidized nanofibers possess higher surface oxygen content than pristine nanofibers. Higher water adsorption capacities on oxidized nanofibers determined by water adsorption isotherms suggest the improvement of surface polarity and hydrophilicity. Furthermore, adsorption isotherms of benzene, butanone and ethanol show that surface oxidation enhances the adsorption tendency for butanone and ethanol on nanofibers due to increased surface polarity, indicating that the adsorption selectivity to polar organic compounds is improved. (C) 2013 Elsevier B.V. All rights reserved.
Effects of Surface Treatment of Carbon Fiber: Tensile Property, Surface Characteristics, and Bonding to Epoxy

Zike Wang,Xiangyu Huang,Guijun Xian,Hui Li

DOI: https://doi.org/10.1002/pc.23489

IF: 5.2

2015-01-01

Polymer Composites

Abstract:In this article, effects of electrochemical oxidation and sizing treatment of PAN‐based carbon fibers (CFs) on the tensile properties, surface characteristics, and bonding to epoxy were investigated. As found, the electrochemical oxidation improves the tensile strength of single CF by 16.0%, due to weakening the surface stress concentration and smoothing the surface structure. Further sizing treatment shows a negligible effect on the tensile strength. Both oxidation and sizing treatments significantly improve the wettability and surface energies of CFs by introducing oxygen‐containing functional groups. Microbond test was conducted to characterize the interfacial shear strength (IFSS) between a single fiber and an epoxy droplet. The oxidation treatment increases IFSS slightly, which is due to the contradictory effects of the formation of chemical bonds between the resin and CFs, and the reduced mechanical interlocking. Further sizing treatment significantly enhances IFSS from 73.6 to 81.0 MPa, due to the formation of vast chemical bonds. Furthermore, the oxidation and sizing treatment can effectively reduce the degradation of IFSS to the hygrothermal ageing for the CF/epoxy system. POLYM. COMPOS., 37:2921–2932, 2016. © 2015 Society of Plastics Engineers
The Effect of Anodic Oxidation Treatment on Interfacial Properties of Composites

CAO Hai-lin,HUANG Yu-dong,ZHANG Zhi-qian,LIU Li-xun

DOI: https://doi.org/10.3969/j.issn.1001-4381.2000.04.005

2000-01-01

Abstract:WT10.25BZ]Anodic oxidation treatment method was used to modify the surface of carbon fibers The chemical composition of carbon fibers surface, the tensile strength of filaments and the interlaminar shear strength (ILSS) were studied respectively The results indicate the number of polar functional groups on the carbon fiber surface and the ILSS of the composites are increased, and the tensile strength of filaments is decreased in a certain scope Meanwhile the mechanism of the anodic oxidation treatment to improve the interfacial property of composites is obtained by analyzing the results
Effects of Anodic Oxidation Treatment for Three Dimensional Carbon Fibre Braided Fabric on Properties of Its Composite

YD Huang,HL Cao,ZQ Zhang

DOI: https://doi.org/10.1179/026708301101509476

IF: 1.8

2001-01-01

Materials Science and Technology

Abstract:An anodic oxidation treatment method is developed in this paper which is capable of modifying the surfaces of carbon fibres in three-dimensional (3D) braided fabrics conveniently and uniformly. The results on the utilisation of this method in the surface treatment of 3D carbon fibre braided fabrics are presented. The effects of anodic oxidation treatment of 3D fabrics on the properties of phenolic resin composites are analysed and discussed. By appropriate treatment, the interfacial shear strength and compressive strength may be improved by 20% and 59.3% respectively. As far as the impact properties of the composites are concerned, the crack initiation energy was increased and the crack propagation energy decreased. Concerning ablative properties of the composites, the linear ablative rate was decreased by 10.7% and the maximum temperature of the underside of the ablative section was reduced by 2.7%.

Effect of Oxidation Treatment on Surface Fractal Dimension of Activated Carbon Fiber

Study on modification of carbon fiber and performance of carbon paper as gas diffusion layer

Research on Surface Treatment of Carbon Fiber and the Conductive Properties of Paper

Chemical Treatment of Carbon Fibers and the Development of Functional Paper

The investigation on microstructure change of activated carbon fiber by oxidation

The Effect of Oxidation Treatment by KClO3/H2SO4 System on Intersurface Performance of Carbon Fibers

Surface modification of carbon fibers by anodic oxidation

Adsorption Of Volatile Organic Compounds In Nitrogen Streams On Oxidized Activated Carbon Fibres

Research on Surface Properties of Modified Activated Carbon Fiber and Its Mercury Adsorption Performance

THE RESEARCH ON TRACTAL OF ACTIATED CARBON FIBER BY NITROGEN ADSORPTION

Study on adsorption performance of polyacrylonitrile-based activated carbon fiber for trace of hexavalent chromium

Comparison of Activated Carbon from Water Bamboo Residues with Surfaces Modified by Different Methods

Study on Carbon Fiber Surface Treatment Based on Surface Oxidation Method

The Effect of Oxidation Treatment with Supercritical Water/Hydrogen Peroxide System on Intersurface Performance for Polyacrylonitrile-Based Carbon Fibers

Influence of Fibre Surface Oxidation Treatment on Mechanical Interfacial Properties of Carbon Fibre/ Polyarylacetylene Composites

The oxidation of carbon fiber on the interlaminar shear strength and tribological properties of high-density polyethylene composites

Experimental and Modeled Results Describing Adsorption of Trace VOCs Onto Oxidized ACF

Surface Oxidation of Activated Electrospun Carbon Nanofibers and Their Adsorption Performance for Benzene, Butanone and Ethanol

Effects of Surface Treatment of Carbon Fiber: Tensile Property, Surface Characteristics, and Bonding to Epoxy

The Effect of Anodic Oxidation Treatment on Interfacial Properties of Composites

Effects of Anodic Oxidation Treatment for Three Dimensional Carbon Fibre Braided Fabric on Properties of Its Composite