Abstract:The wear and corrosion effects in marine or coastal environments are critical issues that seriously deteriorate the service performance of marine infrastructure. Thus, development of an effective and long-lasting wear-resistant and corrosion-resistant protective coating is highly desirable. By controlling the diameter ratio of different heterogeneous metal wires during the supersonic arc spraying process, a laminated-structured Cu-TiN/TiO 2 metal-ceramic composite coating with a Cu content of 8.3 % -66.6 % was fabricated. The effects of Cu loading on the microstructure, morphology, mechanical properties, and wear resistance of composite coating were analyzed. The results of scanning electron microscopy and nanoindentation tests indicated that the composite coating exhibited a dense microstructure, with tight interlayer bonding, and a gradient change in hardness and Young's modulus with Cu loading. The friction and wear tests under different loads and wear environments shown that the composite coating had excellent wear resistance. The composite coating with 8.3 % Cu loading had stronger resistance to plastic deformation and abrasive wear under dry sliding friction with 5 N and 10 N loads. The composite coating with 35.8 % Cu loading shown the most significant lubrication and friction reduction effect of Cu under dry sliding friction at a larger load of 20 N, showing the best wear resistance. The wear test under 10 N load with 3.5 wt% NaCl corrosion solution shown that the composite coating with 8.3 % Cu load had a more prominent role in resisting corrosion wear. These results may guide the preparation of high hardness, wear and corrosion resistant Cu-TiN/TiO 2 metal-ceramic composite coating with appropriate Cu loading capacity through simple and effective preparation methods and easily customized raw materials, according to different wear and corrosion conditions.

Sliding Wear Performance of CuNiCoBe Material

Tribological Characteristics of Silicon Nitride-chilled Cast Iron with Oil-less Lubrication

Study on the Anti-Wear Ability of Shiplock Material

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Torsional Fretting and Torsional Sliding Wear Behaviors of CuNiAl Against 42crmo4 under Dry Condition

A comparative study on torsional fretting and torsional sliding wear of CuNiAl under different lubricated conditions

Friction and wear performance of CrSiBCN coatings sliding against ceramic and metal counterparts in sea water

Mechanical and tribological property of Cu/CrB 2 composites under dry sliding condition

Preparation and properties of Ni-P/Bi self-lubricating composite coating on copper alloys

THE WEAR BEHAVIOR OF BRUSH-PLATED Ni-W-Co/SiC COMPOSITE LAYER WITH OIL LUBRICATION

Effect of Cu content on the wear resistant behavior of arc-sprayed laminated-structured Cu–TiN/TiO 2 composite coating

Study on Friction and Wear Performance of Sliding Metal Seal Materials Under Reciprocating Motion

Insight into the tribological properties of cylinder liner-piston ring under the nano BNNs/Cu composite additive lubrication

A research on the electrical sliding behavior wear of dual-scale particulate reinforced copper matrix composites

Study on the Tribological Performance of Copper-Based Powder Metallurgical Friction Materials with Cu-Coated or Uncoated Graphite Particles as Lubricants

High-pressure wear behavior of laser clad MoNiTaTiV high-entropy alloy coating sliding against QBe2.0 beryllium bronze under dry and oil-lubricated conditions

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Microstructural changes and dry sliding wear behavior of Cu-15Ni-8Sn-0.5Co alloy during deformation and aging treatment

Preparation of the electroless Ni–P and Ni–Cu–P coatings on engine cylinder and their tribological behaviors under bio-oil lubricated conditions

Friction and wear behavior of CuFe3Al powder metallurgical composites in dry sliding

Effect of nano-AlN, Al 2 O 3 on friction and wear properties of copper-steel clad plate immersed in the lubricants