Abstract:Electroless nickel composite coatings have the potential for high-temperature tribological applications, and a combination of high wear resistance and low friction factor is one of the desirable solutions but still a tricky problem. The addition of self-lubricating WS2 and hard Si3N4 nanoparticles to the Ni-P coatings is expected to obtain good high-temperature tribological performance. In this work, Ni-P-Si3N4-WS2 composite coatings with various contents of WS2 nanoparticles were prepared using electroless plating and subsequently annealed at 400 °C in an inert atmosphere. The tribological properties of the coatings were evaluated using a ball-on-disc wear instrument at operating temperatures from 25 to 600 °C. The microstructure, chemical composition, and surface morphology of the coatings were characterized by X-ray diffractometry (XRD), energy disperse spectroscopy (EDS), and scanning electron microscopy (SEM). Upon increasing the WS2 dosage in the bath, the WS2 content in the coating increased and the micro-hardness of the as-plated coating increased from 539 to 717 HV. After heat treatment, the coating underwent a crystallization process, and the hardness increased from 878 to 1094 HV. The main wear mechanism of the coating changed from adhesive wear in the as-plated state to abrasive wear in the annealed state. The annealed Ni-P-Si3N4-WS2 coating with a WS2 dosage of 2.5 g/L in the bath exhibited excellent mechanical properties, with a hardness of 10.9 GPa, a friction coefficient of ~0.51, and a wear rate of 8.4 × 10−15 m3N−1×m−1 at room temperature, and maintained optimal performance at high temperatures. At operating temperatures of 200, 400, and 600 °C, the form of wear was adhesive wear for coatings with a WS2 dosage < 1.5 g/L and abrasive wear for coatings with a WS2 dosage ≥ 1.5 g/L. The synergism of WS2 and Si3N4 particles refined the grains of the Ni-P matrix in as-plated coatings and obviously reduced the friction coefficient of friction pairs in annealed coatings at all operating temperatures.

THE WEAR BEHAVIOR OF BRUSH-PLATED Ni-W-Co/SiC COMPOSITE LAYER WITH OIL LUBRICATION

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Tribological Characteristics of Silicon Nitride-chilled Cast Iron with Oil-less Lubrication

A Comparative Investigation of the Tribological Behavior and Wear Mechanism of Bronze-graphite Composite under Dry- and Water-lubricated Sliding Against Steel

High Temperature Tribology Behaviors of Brush Plated Ni–W–Co/SiC Composite Coating

The Wear Resistance of an Ni-Cu-P Brush Plating Layer on Different Substrates

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Preparation, Mechanical Properties and Wear Resistance of Ni–W/SiC Nanocomposite Coatings

Characterization and Wear Behaviors of Electrodeposited Ni-MoS2/SiC Composite Coating

High Temperature Tribological Behavior of Electroless Plating Ni-P-Si3N4-WS2 Composite Coatings

Dry Wear Behaviors of Wear Resistant Composite Coatings Produced by Laser Cladding

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

Lubricating mechanism of sulfurized olefin on Ni-base brush plating layers

A Study On Abrasive Resistance Of Ni-Based Coatings With A Wc Hard Phase

Preparation and tribological properties of Ni-P electroless composite coating containing inorganic fullerene-like WS2 nanomaterials

Lubricating Mechanism of Sulfurized Olefin on Ni-P Brush Plating Layer

Study of fabrication and wear properties of Ni–SiC composite coatings on A356 aluminum alloy

Friction and Wear of Electroless Ni-P-CS Composite Coating