Properties measurement of intermediate-temperature solid oxide fuel cell

WEI Bo,LIU Wei,SHU Wen-yu,LV Zhe

DOI: https://doi.org/10.3969/j.issn.1005-4642.2012.06.002

2012-01-01

Abstract:The operation mechanism of solid oxide fuel cell was introduced.The open circuit voltage of anode-supported cell,discharge and power curves were measured.The change of cell resistance vs.current density was also analyzed.

What problem does this paper attempt to address?

Simulation and Experimental Measurement of Local Performance of Anode Supported Solid Oxide Fuel Cell

WANG Jie,YAN Dong,ZHU Bin,CHI Bo,PU Jian,ZHANG Yi-sheng,LI Jian

2011-01-01

Journal of Functional Biomaterials

Abstract:In order to prepare for high performance large size anode-supported planar solid oxide fuel cell(SOFC) and avoid the gas distribution difference during the test,in this research single cell with dimension of 10cm×10cm(active reaction area of 9cm×9cm) was divided into 9 galvanically separated segments(each segment with dimension of 2.8cm×2.8cm) to measure the local performance and temperature.Each segment was measured independently about the current-voltage curve and the local temperature.For comparison,computational fluid dynamics(CFD) was used to simulate the gas distribution in the cathode side.Both the simulation and experimental results show an inhomogeneous distribution of gas during the test.This work is crucial to design large size SOFC single cell with optimization of the gas distribution layer.
The method for the conductivity measurement of electrolyte and electrode materials in solid oxide fuel cells

He Beibei,Pan Xin,Xia Changrong

DOI: https://doi.org/10.3969/j.issn.1009-1742.2013.02.010

2013-01-01

Engineering Sciences

Abstract:The conductive mechanism of crystal material,especially of the solid oxide fuel cell components is detailedly discussed in this article.Several influence factors that affect the conductivity of materials are also mentioned.Some commonly used measurements for electrolyte and electrode materials,such as total conductivity,electronic conductivity and ion conductivity measurements are introduced.Besides,the issues which should be noticed are pointed out in these measurements.
Experimental investigation of temperature distribution in solid oxide fuel cells

Yucong Fan,Jiting Jian,Xiucheng Zhang,Shuxue Mei,Yu Zhu,Wenchun Jiang,Shixue Wang

DOI: https://doi.org/10.1016/j.ijhydene.2024.07.009

IF: 7.2

2024-07-13

International Journal of Hydrogen Energy

Abstract:Solid oxide fuel cells (SOFCs) can directly convert the chemical energy in fuels and oxidants into electrical energy because of their high operating temperatures, making them efficient and environmentally friendly. The high-temperature operating characteristic gives SOFCs numerous advantages, including flexible fuel capability and high efficiency. However, it leads to a non-uniform temperature distribution that results in the performance degradation of SOFCs or even system failure. Owing to the high-temperature and gas-sealed operating environment, measuring the temperature distribution in SOFC stacks using experimental methods is extremely difficult. In this study, an SOFC internal temperature measurement device is developed and constructed to investigate the impacts of various factors, including the operating current density and gas flow rate, on the electrical output performance and temperature distribution within an SOFC stack. The experimental results indicate that the SOFC temperature gradually increases with increasing current density. Furthermore, the temperature difference between the spatial locations increases, and the inhomogeneity of the temperature distribution becomes more significant. During the growth of the current density i from 0.1 A/cm 2 to 0.5 A/cm 2 , the maximum temperature gradient on the SOFC electrodes reaches the lowest level at i = 0.3 A/cm 2 . The maximum current density and power density increase as the gas flow rate increases. However, the electrical efficiency and fuel utilization ratio gradually decrease, and the uniformity of the temperature distribution deteriorates. Air flux is the main factor that dominates the temperature distribution in SOFCs. The temperature on the cathode side is higher than that on the anode side. These results contribute to understanding the temperature distribution patterns in SOFCs and provide some guiding significance for SOFC design and operation optimization.

chemistry, physical,electrochemistry,energy & fuels
Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Min-Fang Han,Hui-Yan Yin,Wen-Ting Miao,Su Zhou

DOI: https://doi.org/10.1016/j.ssi.2008.02.035

IF: 3.699

2008-01-01

Solid State Ionics

Abstract:The anode substrates in the planar anode-supported solid oxide fuel cells (SOFC) were prepared by tape calendaring process, as well as the thin electrolyte films for increasing the power density of SOFCs at reduced operation temperature were fabricated by slurry-coating method. The minimization of co-firing temperature for anode and electrolyte layers was investigated by a novel three-step sintering technique in this paper. In order to obtain large three phase boundaries (TBP) at the electrolyte/anode interface, active anode layer was screen printed onto the anode substrate. Dense yttria stabitized zirconia (YSZ) thin films with a 10-15 mu m thickness on porous anode substrates were successfully fabricated by slurry-coating in an YSZ suspension. These three layers were co-fired together at 1300-1350 degrees C. The fuel cells with a diameter of 25 mm, fabricated by this co-firing technique show relatively high power density. The open circuit voltage (OCV) of 1.10 V was observed at 800 degrees C, the maximum power densities are 0.28, 0.51 and 0.95 W cm(-2), at 700, 750 and 800 degrees C, respectively. (C) 2008 Elsevier B.V. All rights reserved.
Experimental Characterization and Elementary Reaction Modeling of Solid Oxide Electrolyte Direct Carbon Fuel Cell

Yixiang Shi,Chen Li,Ningsheng Cai

DOI: https://doi.org/10.1016/j.jpowsour.2013.12.021

IF: 9.2

2011-01-01

Journal of Power Sources

Abstract:The paper presents an elementary reaction based solid oxide fuel cell (SOFC) model coupled with anodic elementary heterogeneous reactions and electrochemical charge transfer reactions for CO/CO2 fuel based on an anode supported button cell. The model is calibrated and validated using experimental data obtained for various CO/CO2 fuel compositions at 750, 800 and 850°C. The comparison shows that the modeling results agree well with the experimental data. The effects of operating conditions on the cell performance and the detailed species concentration distribution are predicted. Then, the carbon deposition on the SOFC anode with CO/CO2 fuel is experimentally measured and simulated using the elementary reaction model. The results indicate that lower temperature and lower operation voltage are helpful to reduce the possibilities of carbon deposition on Ni particle surfaces.
Research of processing techniques used in fabrication of solid oxide fuel cells and study of their selected properties

Jiang Liu,Zhe Lü,Wei Liu,Li Pei,Xin Zhao,Li Jia,Yanbin Song,Xiaomei Liu,Lanying He,Wenhui Su

DOI: https://doi.org/10.1007/BF02879941

1998-01-01

Abstract:The processing techniques used in the fabrication of solid oxide fuel cells (SOFC) were studied. A fast, simple and convenient method of studying and fabricating SOFC was found. The properties of the single cell and the series stack of the SOFC were measured and studied. The maximum open voltage and short current density of the single cell are 1.18V and 360 mA/cm 2 , respectively. And the maximum open voltage and short current density of the series stack of 7 cells are 7.30 and 400 mA/cm 2 respectively and the output power is about 2.0 w. Some simple applications were tried by using the SOFC series stack.
Fabrication and Property of SOFC via Colloidal Spray Coating

Jiao Ding,Wei-min Guo,Jiang Liu

DOI: https://doi.org/10.3321/j.issn:1000-565x.2007.11.016

2007-01-01

Abstract:In this paper, an YSZ electrolyte layer was spray-coated on NiO/YSZ anode substrate, and the corresponding single cell of solid oxide fuel cell (SOFC) was assembled and tested. Then, CHI electrochemical station and SEM were used to test and analyze the voltage-current characteristics, the impedance spectra and the section microstructure of the cell. The test results indicate that the cell works and the open-circuit voltage (OCV) decreases with the increase of the temperature. Concretely, when the temperature increases from 500°C to 800°C, the OCV decreases from 1.054 V to 0.963 V and the maximum power density reaches 57 × 10-3 W/cm2 at 800°C. Moreover, it is found that the interface resistance dominates at low temperature and markedly decreases when the temperature increases, and that the Ohmic resistance of SOFC mainly results from the YSZ electrolyte layer in about 30 μm thickness and the inhomogeneous anode microstructure.
Performance of Anode-Supported Single-Chamber Solid Oxide Fuel Cells

Ai Gang,Lu Zhe,Wei Bo,Huang Xiqiang,Chen Kongfa,Su Wenhui

DOI: https://doi.org/10.3321/j.issn:0253-9837.2006.10.011

IF: 16.5

2006-01-01

Chinese Journal of Catalysis

Abstract:An anode-supported single-chamber solid oxide fuel cell (SC-SOFC) with dense yttria-stabilized zirconia film as the electrolyte was fabricated by the slurry spin coating technique. The single cell exhibited high performance when operated in a mixture of methane, nitrogen, and oxygen. At 700 degrees C, the open current voltage and maximum power density were 1 V and 398 mW/cm(2), respectively. The ohmic resistance was as small as 0.097 Omega center dot cm(2), being 6.4% of the electrode polarization resistance only. Therefore, the anode-supported SC-SOFC with optimized electrode materials is very promising.
Numerical Study on Electric Characteristics and Thermal Stresses of Solid Oxide Fuel Cells

Pengfei Fan,Xiongwen Zhang,Guojun Li

DOI: https://doi.org/10.1115/fuelcell2012-91121

2012-01-01

Abstract:A generalized, three-dimensional (3D) mathematical model of solid oxide fuel cells (SOFCs) for various geometries is constructed in this paper. A finite-volume method is applied to calculate the electric characteristics, which is based on the fundamental conservation law of mass, energy and electrical charge. The electrical potential distribution, the current density distribution, the concentrations distribution of the chemical species and the temperature profile are calculated by solving the governing equations of a single-unit model with double channels of co-flow and counter-flow pattern using the commercial computational fluid dynamic software Fluent. The internal steam reforming and the water shift reactions are taken into account in the mathematical model. The Knudsen diffusion is considered for computation of the gases diffusion in the porous electrodes and the concentration overpotential. The Butler-Volmer equation and the function of the reaction gases composition for the exchange density are used in the model to analyze the activation overpotential. Numerical simulations are performed for a planar geometry solid oxide fuel cell and the detailed features of the temperature, the electrical potential distribution and the gases composition are illustrated. The simulation results agree well with the Benchmark results for planar configuration. With the simulated temperature profile in the planar SOFC, the finite-element method is employed to calculate the thermal stress distribution in the planar solid oxide fuel cell. A 3D finite-element model consists of positive electrode-electrolyte-negative electrode (PEN) and interconnects assembly is constructed by using commercial finite-element code Abaqus. The effects of temperature profile, electrodes and electrolyte thickness, and coefficients of thermal expansion (CTE) mismatch between components are characterized. The calculated results indicate that the maximum stress appears on the electrode and electrolyte interface. The value and distribution of the thermal stress are the functions of the applied materials CTE, applied temperature profiles and the thicknesses of electrode and electrolyte. The calculated results can be applied as the guide for the SOFC materials selection and the SOFC structure design.
Numerical Simulation and Experimental Characterization of the Performance Evolution of A Liquid Antimony Anode Fuel Cell

Tianyu Cao,Yixiang Shi,Hongjian Wang,Ningsheng Cai

DOI: https://doi.org/10.1016/j.jpowsour.2015.03.071

IF: 9.2

2015-01-01

Journal of Power Sources

Abstract:A solid oxide fuel cell (SOFC) with a liquid antimony anode is fabricated based on a smooth single crystal YSZ electrolyte substrate and a porous Pt cathode. The performance of the liquid antimony anode was tested under “battery mode”, with the anode chamber shielded in argon throughout the test and the cathode exposed to air. Polarization curves were taken and a long term constant potential discharging test was carried out afterwards. Taking electrochemical reaction, mass transport and microstructure of the liquid Sb anode into consideration, a one dimensional mathematical model was built and then validated by the polarization curve and the constant potential discharging performance curve obtained during the test. This model analyzes the metallic Sb distribution in the anode during cell operation, explains the cell performance evolution base on the microstructural development of the liquid Sb anode and simulates how the anode microstructure affects the cell performance.
Microstructure and electrochemical characterization of solid oxide fuel cells fabricated by co-tape casting

Xiaoliang Zhou,Kening Sun,Jie Gao,Shiru Le,Naiqing Zhang,Peng Wang

DOI: https://doi.org/10.1016/j.jpowsour.2009.02.008

IF: 9.2

2009-01-01

Journal of Power Sources

Abstract:A co-tape casting technique was applied to fabricate electrolyte/anode for solid oxide fuel cells. YSZ and NiO–YSZ powders are raw materials for electrolyte and anode, respectively. Through adjusting the Polyvinyl Butyral (PVB) amount in slurry, the co-sintering temperature for electrolyte/anode could be dropped. After being co-sintered at 1400°C for 5h, the half-cells with dense electrolytes and large three phase boundaries were obtained. The improved unit cell exhibited a maximum power density of 589mWcm−2 at 800°C. At the voltage of 0.7V, the current densities of the cell reached 667mAcm−2. When the electrolyte and the anode were cast within one step and sintered together at 1250°C for 5h and the thickness of electrolyte was controlled exactly at 20μm, the open-circuit voltage (OCV) of the cell could reach 1.11V at 800°C and the maximum power densities were 739, 950 and 1222mWcm−2 at 750, 800 and 850°C, respectively, with H2 as the fuel under a flow rate of 50sccm and the cathode exposed to the stationary air. Under the voltage of 0.7V, the current densities of cell were 875, 1126 and 1501mAcm−2, respectively. These are attributed to the large anode three phase boundaries and uniform electrolyte obtained under the lower sintering temperature. The electrochemical characteristics of the cells were investigated and discussed.
Development and Performance Analysis of New Planar Solid Oxide Fuel Cell

Yu-zhang WANG,Jian-guo YU,Yu HUI,Shi-lie WENG

DOI: https://doi.org/10.3321/j.issn:1000-6761.2008.06.026

2008-01-01

Abstract:Based on commercial CFD software and experimental performance data of fuel cell components,the software package used to analyze complicated physical process of single cell of solid oxide fuel cell(SOFC) was improved.Distribution laws of gas components concentration,temperature,electric potential,current and current density of new developed planar SOFC 's single cell were obtained using the above software package.Results show that,at a high fuel efficiency,polarization loss of concentration caused by components diffusion in anode is one of the most important factors influencing cell performance.This new kind of fuel cell is able to improve leak tightness efficiently.However,its electrolyte should be with higher maximum ionic conductivity.
Electrochemical Performance of (ba0.5sr0.5)0.9sm0.1co0.8fe0.2o3−δ As an Intermediate Temperature Solid Oxide Fuel Cell Cathode

Shuyan Li,Zhe Lu,Na Ai,Kongfa Chen,Wenhui Su

DOI: https://doi.org/10.1016/j.jpowsour.2006.11.022

IF: 9.2

2007-01-01

Journal of Power Sources

Abstract:This study presents the electrochemical performance of (Ba0.5Sr0.5)0.9Sm0.1Co0.8Fe0.2O3−δ (BSSCF) as a cathode material for intermediate temperature solid oxide fuel cells (IT-SOFC). AC-impedance analyses were carried on an electrolyte supported BSSCF/Sm0.2Ce0.8O1.9 (SDC)/Ag half-cell and a Ba0.5Sr0.5Co0.8Fe0.2O3−δ (BSCF)/SDC/Ag half-cell. In contrast to the BSCF cathode half-cell, the total resistance of the BSSCF cathode half-cell was lower, e.g., at 550°C; the values for the BSSCF and BSCF were 1.54 and 2.33Ωcm2, respectively. The cell performance measurements were conducted on a Ni-SDC anode supported single cell using a SDC thin film as electrolyte, and BSSCF layer as cathode. The maximum power densities were 681mWcm−2 at 600°C and 820mWcm−2 at 650°C.
Study of Operating Conditions for High Efficiency and Anode Safety of Industrial-Size Solid Oxide Fuel Cell

Wang Yige,Li Hangyue,Lyu Zewei,Han Minfang,Sun Kaihua

DOI: https://doi.org/10.6023/a22010041

2022-01-01

Abstract:Solid oxide fuel cell (SOFC) has been regarded as one of the promising energy conversion technologies since it provides higher efficiency and lower pollution than conventional power systems. How to improve the SOFC efficiency is one of the focus issues in both industry and academia. Besides, when industrial-size SOFC is operated at high fuel utilization (U-fuel) to achieve high efficiency, the Ni anode in the downstream region may be locally oxidized due to the high oxygen partial pressure. Thus, operating conditions for both high efficiency and anode safety are required. In this work, a method for the measurement and evaluation of SOFC efficiency was established. By comparing the test results under different conditions (current, fuel flow rate, and temperature) with high fuel utilization, it was found that at the same fuel utilization, the voltage decreased as the current increased. Therefore, the lower current is beneficial for higher efficiency, while the higher current is beneficial for higher power. The relationship between voltage fluctuation and local oxidation of anode during operation at high fuel utilization was also studied. After analyzing the critical condition of Ni oxidation, the cell output voltage higher than the critical electromotive force of Ni oxidation was proposed as the safe operating condition to prevent local oxidation of anode. Based on the cell samples and test parameters used in this work, it was found a high efficiency of over 50% was corresponding to the fuel utilization range of 77% to 90%. And the maximum electrical efficiency was always corresponding to U-fuel=87.10%. Although the operating conditions corresponding to the maximum efficiency of SOFC cells or stacks with different materials, structures, and fabrication processes may vary, the measurement and evaluation methods, as well as the judgment of the safe operating condition proposed in this study, are still helpful. In practical application, the operating conditions could be determined based on such testing results according to the importance of efficiency, power and long-term stability.
Electrochemical characterization methods of the key materials for SOFC

Fan Liquan,Zhao Erqing,Gao Keqing,Xiong Yueping

DOI: https://doi.org/10.3969/j.issn.1009-1742.2013.02.009

2013-01-01

Engineering Sciences

Abstract:Solid oxide fuel cells(SOFCs)are the solid-state devices for generating electricity from the chemical energy.The effect of solid oxide materials on the performance of SOFC is especially important.From the influence of materials on electrochemical performance of SOFC,this paper summarizes electrochemical characterization methods for the composition materials of SOFC briefly based on the fundamentals of electrochemistry and solid electrochemistry.Some research experience is also included in the paper,which can facilitate the further research of materials.
Development of Solid Oxide Fuel Cell Materials for Intermediate-to-low Temperature Operation

Jianbing Huang,Fucheng Xie,Cheng Wang,Zongqiang Mao

DOI: https://doi.org/10.1016/j.ijhydene.2011.04.030

IF: 7.2

2011-01-01

International Journal of Hydrogen Energy

Abstract:The commercialization of solid oxide fuel cell (SOFC) needs the development of functional materials for intermediate-to-low temperature (400-700 degrees C, ILT) operation. Recently, we have successfully developed new electrolyte materials for ILT-SOFCs, including Ce0.8Sm0.2O1.9 (SDC), BaCe0.8Sm0.2O2.9 (BCSO) and SDC-carbonate composites. Compared with the state-of-the-art yttria-stabilized zirconia (YSZ), these materials exhibit much higher ionic conductivity at ILT range. Especially, SDC-carbonate composites show an ionic conductivity of 10(-2) to 1 Scm(-1) between 400 and 600 degrees C in fuel cell environment. Some new cathode materials were investigated for above electrolyte materials and showed promising performance. Alternative anode materials were developed to directly utilize alcohol fuels. A dry-pressing and co-firing process was employed to fabricate thin SDC and BCSO electrolyte membranes as well as thick SDC-carbonate composite electrolyte with acceptable density on anode substrate. Many efforts have also been made on fabrication of larger-size planar cells and exploitation of reliable sealing materials. Copyright (C) 2011, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
Effect of Anodes on the Performance of YSZ Thin Film SOFC

CHEN Kong-fa,LU Zhe,AI Na,SU Wen-hui

DOI: https://doi.org/10.3969/j.issn.1001-1579.2007.02.023

2007-01-01

Abstract:The effects of two kinds of anodes on the performance of YSZ thin film solid oxide fuel cell(SOFC) were studied.The YSZ films cells fabricated on NiO-YSZ anode and NiO-SDC-YSZ anode produced open-circuit voltage of 1.09 V and 0.87 V and the maximum power density of 0.86 W/cm2 and 0.16 W/cm2 at 800 ℃,respectively.The total electrode resistance of the cell with NiO-SDC-YSZ anode was 58% higher than that of the cell with NiO-YSZ anode.
Numerical study on electric characteristics of solid oxide fuel cells

X ZHANG,G LI,J LI,Z FENG

DOI: https://doi.org/10.1016/j.enconman.2006.08.011

IF: 10.4

2007-01-01

Energy Conversion and Management

Abstract:Numerical simulations are performed in both planar and tubular geometries of a solid oxide fuel cell to study the electric characteristics. The Navier–Stokes equations are solved with an electrochemical model developed in this paper, which is a generalized, three dimensional complete polarization electrochemical model for solid oxide fuel cells with various geometries. This study conducts detailed analyses of the electric polarizations for both planar and tubular solid oxide fuel cells and presents the characteristics of the density and the potential distribution in the electric components for the planar co-flow solid oxide fuel cell. The ohmic heats in the planar and tubular configuration solid oxide fuel cell are also compared and discussed.
Theoretical Analysis of the Characteristics of the Solid Oxide Fuel Cells with a Bi-Layer Electrolyte

Shuanglin Shen,Liejin Guo,Hongtan Liu

DOI: https://doi.org/10.1016/j.ijhydene.2013.03.035

IF: 7.2

2013-01-01

International Journal of Hydrogen Energy

Abstract:From the analytical model derived earlier [17], analytical expressions for the relative thickness ratio rs of a bi-layer electrolyte and the maximum power density of a fuel cell are developed. Using these expressions, together with the other relationships from the analytical model, the characteristics of solid oxide fuel cells (SOFCs) with a bi-layer electrolyte are analyzed and theoretical analysis of the effect of the configuration of a bi-layer electrolyte on the SOFC performance is performed. The results show that the effectiveness of the bi-layer electrolyte depends strongly on its configuration. In the analyses, the variations of open circuit voltage and the maximum power density with the thickness ratio at different total electrolyte thicknesses and different operating temperatures are obtained. Furthermore, by taking into considerations of the oxygen partial pressure at the interface between the two layers of electrolytes, an analytical expression for the critical relative thickness ratio, above which, the electrolyte is stable, is obtained.
An Experimental Evaluation of the Temperature Gradient in Solid Oxide Fuel Cells

Bertrand Morel,Réal Roberge,Sylvio Savoie,Teko W. Napporn,Michel Meunier

DOI: https://doi.org/10.1149/1.2398729

2007-01-01

Abstract:Solid oxide fuel cells (SOFCs) working under direct reforming or catalytic partial oxidation may experience severe thermal gradients due to cooling or overheating at the fuel cell inlet. In this work, we show that the ohmic resistance measurement of thick electrolyte cells composed of smaller cathodes displaced along the opposite side of a full-size anode provides excellent results to evaluate the temperature gradients along cells submitted to such processes. Taking the catalytic partial oxidation of methane in single-chamber SOFC, as an example, we evaluate an overheating of more than within the first centimeter length of the cell. Solid oxide fuel cells (SOFCs) working under direct reforming or catalytic partial oxidation may experience severe thermal gradients due to cooling or overheating at the fuel cell inlet. In this work, we show that the ohmic resistance measurement of thick electrolyte cells composed of smaller cathodes displaced along the opposite side of a full-size anode provides excellent results to evaluate the temperature gradients along cells submitted to such processes. Taking the catalytic partial oxidation of methane in single-chamber SOFC, as an example, we evaluate an overheating of more than within the first centimeter length of the cell. Export citation and abstract BibTeX RIS

Properties measurement of intermediate-temperature solid oxide fuel cell

Simulation and Experimental Measurement of Local Performance of Anode Supported Solid Oxide Fuel Cell

The method for the conductivity measurement of electrolyte and electrode materials in solid oxide fuel cells

Experimental investigation of temperature distribution in solid oxide fuel cells

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Experimental Characterization and Elementary Reaction Modeling of Solid Oxide Electrolyte Direct Carbon Fuel Cell

Research of processing techniques used in fabrication of solid oxide fuel cells and study of their selected properties

Fabrication and Property of SOFC via Colloidal Spray Coating

Performance of Anode-Supported Single-Chamber Solid Oxide Fuel Cells

Numerical Study on Electric Characteristics and Thermal Stresses of Solid Oxide Fuel Cells

Numerical Simulation and Experimental Characterization of the Performance Evolution of A Liquid Antimony Anode Fuel Cell

Microstructure and electrochemical characterization of solid oxide fuel cells fabricated by co-tape casting

Development and Performance Analysis of New Planar Solid Oxide Fuel Cell

Electrochemical Performance of (ba0.5sr0.5)0.9sm0.1co0.8fe0.2o3−δ As an Intermediate Temperature Solid Oxide Fuel Cell Cathode

Study of Operating Conditions for High Efficiency and Anode Safety of Industrial-Size Solid Oxide Fuel Cell

Electrochemical characterization methods of the key materials for SOFC

Development of Solid Oxide Fuel Cell Materials for Intermediate-to-low Temperature Operation

Effect of Anodes on the Performance of YSZ Thin Film SOFC

Numerical study on electric characteristics of solid oxide fuel cells

Theoretical Analysis of the Characteristics of the Solid Oxide Fuel Cells with a Bi-Layer Electrolyte

An Experimental Evaluation of the Temperature Gradient in Solid Oxide Fuel Cells