Abstract:Sm0.2Ce0.8O1.9 (SDC)-impregnated La0.7Sr0.3MnO3 (LSM) composite cathodes were fabricated on anode-supported yttria-stabilized zirconia (YSZ) thin films. Electrochemical performances of the solid oxide fuel cells (SOFCs) were investigated in the present study. Four single cells, i.e., Cell-1, Cell-2, Cell-3 and Cell-4 were obtained after the fabrication of four different cathodes, i.e., pure LSM and SDC/LSM composites in the weight ratios of 25/75, 36/64 and 42/58, respectively. Impedance spectra under open-circuit conditions showed that the cathode performance was gradually improved with the increasing SDC loading. Similarly, the maximum power densities (MPD) of the four cells were increased with the SDC amount below 700°C. Whereas, the cell performance of Cell-4 was lower than that of Cell-3 at 800°C, arising from the increased concentration polarization at high current densities. This was caused by the lowered porosity with the impregnation cycle. This disadvantage could be suppressed by lowering the operating temperature or by increasing the oxygen concentration at the cathode side. The ratio of electrode polarization loss in the total voltage drop versus current density showed that the cell performance was primarily determined by the electrode polarization. The contribution of the ohmic resistance was increased when the operating temperature was lowered. When a 100mlmin−1 oxygen flow was introduced to the cathode side, Cell-3 produced MPDs of 1905, 1587 and 1179mWcm−2 at 800, 750 and 700°C, respectively. The high cell outputs demonstrated the merits of the novel and effective SDC-impregnated LSM cathodes.

Effect of Anodes on the Performance of YSZ Thin Film SOFC

YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet

Effect of co-sintering temperature on the performance of SOFC with YSZ electrolyte thin films fabricated by dip-coating method

Effect of Sdc-Impregnated Lsm Cathodes on the Performance of Anode-Supported Ysz Films for Sofcs

Fabrication and Performance Test of Solid Oxide Fuel Cells with Screen-Printed Yttria-Stabilized Zirconia Electrolyte Membranes

Impact of yttria-stabilized zirconia contents in nickel cermet anodes for intermediate temperature-operated syngas-fueled thin film solid oxide fuel cells

Effect of Composition of NiO/YSZ Anode on the Polarization Characteristics of SOFC Fabricated by Atmospheric Plasma Spraying

Effect of Composite Pore-Former on the Fabrication and Performance of Anode-Supported Membranes for SOFCs

Development of Lsm-Based Cathodes for Solid Oxide Fuel Cells Based on Ysz Films

Effects of Initial Reduction Temperature on the Microstructures and Performances of Ni/YSZ Anodes for Solid Oxide Fuel Cells

Effects of Electrode Composition and Thickness on the Mechanical Performance of a Solid Oxide Fuel Cell

Effect of Preparation Methods on the Properties of Ni-Ysz Cermets for Sofc Anodes

Study of NiO/YSZ Anode for SOFC Prepared by Tape Casting

Effect of NiO/YSZ Compositions on the Co-Sintering Process of Anode-Supported Fuel Cell

A Comparison of La0.75Sr0.25Cr0.5Mn0.5O3−δ and Ni Impregnated Porous YSZ Anodes Fabricated in Two Different Ways for SOFCs

Preparation of SDC Interlayer and Influence on Performances of Anode Supported Solid Oxide Fuel Cells

Experimental Study On Effect Of Compaction Pressure On Performance Of Sofc Anodes

Study on Preparation of YSZ Film by Electrophoretic Deposition under Constant Current and Its Application in SOFCs

Performance of an Anode-Supported SOFC with Anode Functional Layers

The effect of nickel oxide microstructure on the performance of Ni–YSZ anode-supported SOFCs

Performance and Optimization of Ni/3 Mol% Y2O3-ZrO2 Anode Supported SOFC