Thermal stress analysis and study of valves

LIU Jin-liang,LIU Ming,XIAO Wen-dong,YE Xi-zhong,WANG Zhong-cheng

2012-01-01

Abstract:The relation between compressive stress and thermal stress is described.And the minimum wall thickness under coupling stress is given through the optimal analysis.Meanwhile,this thesis also makes a comparative analysis for the application method of thermal load.

What problem does this paper attempt to address?

Simulation and analysis of dynamic heat transfer inside a cryogenic valve under cryogenic test

Jin Tao,Xia Yuliang,Hong Jianping,Tang Ke,Chen Guobang,Zhang Xiaozhong,Chen Youjun

DOI: https://doi.org/10.3969/j.issn.1000-6516.2007.04.008

IF: 2.134

2007-01-01

Cryogenics

Abstract:Based on the heat transfer coefficient of stainless steel emerged in liquid nitrogen,obtained from experiential equations and revised with experimental measurement,numerical simulation has been carried out on a cryogenic valve to analyze its dynamic heat transfer characteristics under cryogenic tests.The analysis focuses on the cool-down temperatures at four locations on the valve,i.e.,inner surface,outer surface,valve clack and top of packing gland.In order to avoid the temperature at the top of packing gland reaching as low as 0 ℃,and then the occurrence of freezing,an insulating layer is proposed to be attached to the valve stem section inside low temperature nitrogen gas.Further simulation has also been done to predict the effect of the addition of insulating layer.
Thermo-mechanical Stress Analysis of Feed-Water Valves in Nuclear Power Plants

Wen-qing Li,Lei Zhao,Yang Yue,Jia-yi Wu,Zhi-jiang Jin,Jin-yuan Qian

DOI: https://doi.org/10.1016/j.net.2021.09.018

IF: 2.817

2022-01-01

Nuclear Engineering and Technology

Abstract:Feed-water valves (FWVs) are used to regulate the flow rate of water entering steam generators, which are very important devices in nuclear power plants. Due to the working environment of relatively high pressure and temperature, there is strength failure problem of valve body in some cases. Based on the thermo-fluid-solid coupling model, the valve body stress of the feed-water valve in the opening process is investigated. The flow field characteristics inside the valve and temperature change of the valve body with time are studied. The stress analysis of the valve body is carried out considering mechanical stress and thermal stress comprehensively. The results show that the area with relatively high-velocity area moves gradually from the bottom of the cross section to the top of the cross section with the increase of the opening degree. The whole valve body reaches the same temperature of 250 degrees C at the time of 1894 s. The maximum stress of the valve body meets the design requirements by stress assessment. This work can be referred for the design of FWVs and other similar valves. (C) 2021 Korean Nuclear Society, Published by Elsevier Korea LLC.
Research on Fluid Dynamics and Thermal Characteristics in Hydraulic Valves by Thermal-Fluid-Solid Coupling Method

Jia-xi Nie,Zhen-hao Lin,Jiao-shan Hao,Yong-bing Jiang,Zhi-jiang Jin,Jin-yuan Qian

DOI: https://doi.org/10.1115/fedsm2022-86878

2022-01-01

Abstract:Hydraulic valve is used as an important hydraulic component, playing a vital role in fluid power transmission and control systems. When the phenomenon of sticking of valve core occurs, it may seriously decrease the accuracy and sensitivity of the hydraulic valve. Micro-deformation is one of the most common faults causing the valve core sticking, which is due to the thermal load. Therefore, studying the mechanism of valve core sticking caused by thermal fluid is of great significance. In this paper, the fluid dynamics in hydraulic valves and the temperature characteristics of valve core are analyzed based on the thermal-fluid-solid coupling method. Results show that the jet angle (theta) will decrease with the increase of opening degree (k), and the maximum velocity and temperature increase with the increase of the opening degree. By loading the temperature field into the thermal analysis as a boundary condition, it shows that the temperature of the U-throttle groove increases with the increase of the opening degree. In addition, with the increase of opening degree, the maximum thermal deformation increases and the contact pressure between valve core and valve body also increases. This work has a certain reference value for researching and improving the phenomenon of valve core stuck in hydraulic valve.
The Temperature and Thermal Stress Analysis of Steam Pipe and Correlative Branch Pipe with Finite Element Method

Mu-zi LIANG,Jie WEN,Xian-hua CHENG,Li-yuan HU

DOI: https://doi.org/10.3321/j.issn:1006-2467.2007.12.007

2007-01-01

Abstract:Temperature and thermal stress analysis of the steam pipe and correlative branch pipe in thermal power plant was performed using the finite element analysis software ANSYS.The 3D temperature field and the thermal stress distribution can be obtained by the boundary condition,which is the result of the computation through the empirical formula and computer programming.In the running time of scene,the maximum values of the thermal gradient and VonMises thermal stress occur at the conjunction of the steam pipe and its branch pipe.Because those values are beyond the scope of the material's admissible stress,cracks can easily be produced.The result of the two methods above proves the same trend of thermal stress changes.However,compared with the empirical formula,the computer programming is not so empirical and has more engineering application.
Valve Body’ s Thermal Characteristics Analysis for High-Temperature Electrical Gate Valves and Its Optimal Design

Wei-dong YANG,Yue-qiang ZHANG,Zao-xiao ZHANG

DOI: https://doi.org/10.3969/j.issn.0254-6094.2016.03.013

2016-01-01

Abstract:Having Ansys Workbench thermal-structural coupling based to analyze thermal characteristics of valve body structure was implemented, including the optimal design of plate rib’ s size;and the valve body’ s physical model under normal working conditions can be similarly regarded as the heat conduction of area-alter-able ribs;and in the Ansys Workbench, through having the materials added and grids divided and the bounda-ry conditions set, the valve body’ s working condition of high-temperature electrical gate valve was simulated to obtain the distributions of valve body’ s temperature, thermal strain, overall deformation and the equivalent stress;through optimizing the size of plate ribs, the relationship between plate rib’ s sizeδ, H and the thermal strain, overall deformation and the maximum equivalent stress can be reached ,so does the optimized size of plate ribs.
Analysis of the Temperature and Stress Field in a Steam Turbine Bypass Valve Body

LIN Peng,ZHANG Rui-feng,YU Ya-hui,Lu Guang-yao

2011-01-01

Abstract:By using a finite element analytic method,simulated and analyzed was a steam turbine bypass valve in a 330 MW power plant.Under the off-design and rated load operating regimes,the temperature and stress field of the valve body were analyzed.Therefore,the law governing the change of the temperature field and its corresponding stress field at different operating regimes was obtained.Among these operating regimes,the temperature gradient at the inlet of the valve body attains the maximum value under the off-design operating regimes and the overall stress value also hits its maximum,reaching 68.8 MPa.Under the rated load operating regime,the overall stress of the valve body first decreases and then increases with an increase of the opening time duration followed by a decrease until it becomes stable.The maximal stress emerges at 368.5 s,assessed at 85.6 MPa.Furthermore,the authors have also analyzed and evaluated the safety of the steam turbine bypass valve.
Study Of Thermal Stress Distribution On Thick Wall Cylinder By Thermal Shock Treatment

Yingwei Yun,Il-Young Jang,Xiangguo Wu

2007-01-01

Abstract:According to the property of shock, this paper carried out theoretical analysis of thick wall cylinder shell under thermal shock treatment, then an analytical solution of temperature field was obtained by Laplace transform. Based on the temperature solution above, the thermal stress response of thick wall cylinder was solved. And then, the variations of the temperature field, thermal stress field with time, cylinder radius ratio were discussed. The exploration in this paper will lay a theoretical reference to further study on the decrease of fatigue damage of the Super-high pressure tubular reactor under thermal punch.
Numerical Study On Temperature Field And Spool Deformation Of Throttle Slide Valve With V-Notches

Ruijun Wang,Xueming Shao,Jian Deng,Xin Fu

2009-01-01

Abstract:The numerical fluid-solid coupling method is used to simulate the temperature Field and spool radial deformation of the valve with V-notches. The relationships among structural parameters, work pressure drop and temperature field, as well as spool deformation are Studied. Viscous heating effect of the flow inside the valve is an important source of the temperature increment, and spool deformation caused by hydraulic oil heating Could result in spool stick. The numerical results show that notch structural parameters together with work pressure drop are important influential factors for the temperature distribution inside the valve. And spool temperature field has direct influence on radial deformation distribution of the spool.
Analysis of Computers Simulation of ThermalStress in Coking of Shaping Coal

Xiaodong Zhang,yuanzong Li

DOI: https://doi.org/10.3969/j.issn.1007-9432.2001.01.003

2001-01-01

Abstract:The thesis establishs the mathematics model of thermal stress in coking of shaping coal. The effection of parameters on thermal stress and gives some advice on eliminating flaw is analyzed.
Numerical Simulation of Temperature Field and Stress Field of the Valve Box of a Steam Turbine

LI De-sheng,JING Jian-ping,MENG-guang

DOI: https://doi.org/10.3969/j.issn.1001-5884.2008.01.002

2008-01-01

Abstract:Through the use of a structural-analysis finite element method,calculation was conducted to temperature field,thermal stress field and comprehensive stress field of the valve body of a pint-sized steam turbine under the cold startup condition.The detailed temperature fields at key points as well as the variation relationship of its corresponding thermal stress fields were obtained.Moreover,the valve body service life also was evaluated at key points.In addition,the velocity vector field of the fluidity inside valve was simulated by using computational fluid dynamics software.
Stress-Strain Analysis of Reducing Pipe Under Temperature

Jinghong XUE,Yanghua CHU

DOI: https://doi.org/10.3969/j.issn.1674-8425(z).2017.08.008

2017-01-01

Abstract:In the event of thermal expansion and contraction in the pipeline, thermal stress is generated.Due to the existence of thermal stress, the pipe is stretched and contracted to cause deformation of the pipe and damage may occur at the pipe diameter.In this paper, the finite element software ANSYS is used for modeling and analysis, and the eight-node solid solid element model is used to simulate the variable pipe.The influence of temperature on the diameter of the pipeline is studied.The influence of the temperature difference on the variable pipe is studied.The results show that the weak position of the variable pipe is located around the change of the pipeline under the action of temperature.The limit stress of the variable pipe is related to the temperature and temperature of the pipeline.The study provides a reference for the design of thermal pipelines, making the heat transfer variable diameter pipeline design reasonable energy saving.
TEMPERATURE FIELD AND THERMAL STRESS FINITE ELEMENT ANALYSIS OF A 50MW STEAM TURBINE'S CYLINDER IN A POWER PLANT

李益民,李中华,王华,陈强,陈聪智

DOI: https://doi.org/10.3969/j.issn.1002-3364.2003.09.006

2003-01-01

Abstract:A three dimentional finite element analysis of the temperature field and the thermal stress field regarding a 50MW steam turbine's high pressure cylinder in a powr plant under different operation conditions has been carried out. The results show, the position of calculated max. stress tallies completely with that of the cracked cylinder, providing important technical basis for evaluating the steam cylinder's safety and calculating the said cylinder's residual service-life.
Thermal Stress Considered in Design of Jacketed Vessel

YANG Si-hai

DOI: https://doi.org/10.3969/j.issn.1009-3281.2009.06.003

2009-01-01

Abstract:The working condition that the vessel was subjected to external pressure and axial pressure simultaneously was taken into account,the calculation for this jacketed vessel was carried out.The influence of thermal stress to the instability of the vessel was analyzed. Then,the problems which may appear in the design and the solutions for these problems were presented.
Research on Flow Filed and Stress Characteristics of Labyrinth Regulating Valve for Supercritical Thermal Power

YAO Wuping,SONG Hui,GU Weiguo,GUO Weizhong,WANG Dezhong

2013-01-01

Abstract:To investigate the labyrinth channel structure of labyrinth regulating valve'for supercritical thermal power plant under conditions of high-temperature high-pressure with steam medium,the fluid field was calculated by using CFD method,which had been verified by experimental data.The disc stress field was calculated by using one-dimensional fluid solid coupling method.And then it analyzes the impact of chamfer,channel depth,inlet &outlet width and disc thickness on the channel flow field and disc stress field.The results show that the chamfer,inlet width and channel depth have greater impact on flow than that of outlet width;inlet width and disc thickness have greater impact on stress than that of the chamfer.
Stress analysis of heat exchange tube with inner and outer fins under convection heat transfer conditions

Wang Qiu-wang

2011-01-01

Abstract:The heat exchange tube with inner and outer fins has been widely applied in industry in order to enhance the performance of heat exchangers.When it is used in high temperature environment,the security must be considered.A three-dimension model was established to simulate the thermal stress by software ANSYS.The results indicated that the main factor,which had effect on the stress and deformation,was temperature and the maximum stress occurred at the joint location between inner fins and tubes.The inner pressure distribution of tube could enhance the effect of stress.On the contrary,the outer could weaken the effect.
Analysis on Thermal Stress of SV Used in Continuous Casting and Improvement of Its Shape

Xuhong Guo

2010-01-01

Abstract:For preventing the formation of parallel cracks in slide gate valve plate (SV),its shape was improved based on traditional structure. Firstly,two-dimension plane stress finite element models of three type SV were built by simplifying their structure and boundary conditions,then a contrastive analysis of their thermal stress was carried out. The results show that the new SV can prevent the formation of the second and the third kind cracks better,and the prestress can be imposed easily.
A Generalized Thermal Deviation Factor to Evaluate the Comprehensive Stress of Tubes under Non-Uniform Heating

X. L. Li,G. X. Li,G. H. Tang,Y. H. Fan,D. L. Yang

DOI: https://doi.org/10.1016/j.energy.2022.125710

IF: 9

2023-01-01

Energy

Abstract:The heaters working with supercritical fluids normally suffer from high temperature, high pressure and non-uniform heating, which would lead to thermal fragile and stress failure in practical engineering. However, efficient and accurate methods to predict the comprehensive stress in non-uniformly heating tubes are missing. Besides, to reduce the comprehensive stress, a criterion is required to provide optimization guidance of non-uniformly heating tubes. In present study, the thermal and mechanical performances of three typical non-uniformly heating tubes are numerically investigated using the FVM-FEM method. A generalized thermal deviation factor (GTDF) is then proposed. The results showed that the GTDF can accurately predict the ratio of comprehensive stress to yield strength and GTDF > 1 indicates the plastic deformation, which is much more convenient and efficient than the conventional structural analysis. Based on the GTDF, two methods of reducing heat flux non-uniformity and enhancing tube-inside heat transfer are proposed to reduce the comprehensive stress. The results show that the unilaterally elliptic dimpled tube reduces the maximum comprehensive stress by 30.8% compared with the smooth tube and also prevents the stress concentration in the dimple zone, which can be employed to reduce the comprehensive stress in various tubes under non-uniformly heating conditions.
THERMAL STRESS ANALYSIS ON WIRE WINDED SUBDIVIDED-COMBINED LARGE EXTRUSION CONTAINER

LIU Chang-yong,ZHANG Ren-ji,YAN Yong-nian,LIN Feng,ZHANG Lei

2011-01-01

Abstract:Wire winded subdivided-combined extrusion containers has a wide range of advantages over traditional extrusion containers such as lower weight,improved fatigue performance,easier to manufacture and lower cost.Classic analytical solutions are derived without considering the influence of temperature which apparently cannot be applied to design a hot extrusion container.The theoretical derivation of stress distribution based on the consumption of a one-dimensional steady state temperature field was conducted.The analytical solution was obtained using linear thermoelasticity,wire winding theory and elasticity.The theoretical analysis and calculations indicate that the pre-stress factor and inner surface temperature of the container have important influence on the thermal stress distribution of the container.Thermal stress can be reduced to a value which is lower than the allowed stress by adjusting the inner surface temperature and pre-stress factor.Extrusion containers designed by this method have been applied to the 360MN/150MN vertical extrusion equipments.
Fluid-solid-heat Coupling Deformation Analysis of the Valve Trims in a Multistage Pressure Reducing Valve

Dongtao Xu,Changrong Ge,Ying Li,Yuejuan Liu

DOI: https://doi.org/10.1371/journal.pone.0263076

IF: 3.7

2022-01-01

PLoS ONE

Abstract:A multistage pressure reducing valve with specially designed pressure reducing components is presented in this paper. As the deformation of the valve trims under fluid-solid-heat coupling has an important influence on the operation reliability of the valve, a numerical simulation is carried out to analyse the flow field characteristic in the valve and radial deformation of the valve trims using the ANSYS software. And a deformation experiment is designed to validate the deformations of the valve trims at high temperature of 693.15 K. The results indicate that the simulation results agree well with the experimental data. Moreover, it is found that the temperature field has the most significant influence on the deformation of the valve trims, the radial deformations of the matching surface vary from 0.439 to 0.442 mm. And the radial deformations caused by other factors vary from 0.005 to 0.015 mm. In addition, as a novel indicator, the clearance after deformation of the matching surface is used to evaluate the operation reliability of the valve. By using the GAP function in ANSYS static module, the clearances of the matching surface are obtained at different openings under the condition of fluid-solid-heat coupling, further indicating that the initial clearance between the valve plug and inner sleeve should be greater than 0.014 mm to ensure the operation reliability of the valve.
Stress Analysis of Ellipsoidal Head with Heating Spiral

Jun Shen,Heng Peng,Yanfang Tang,Xuemei Liu,Yinghua Liu

DOI: https://doi.org/10.1115/pvp2017-65494

2017-01-01

Abstract:The thermal load is one of important design condition that should be considered carefully in engineering practice. In most instances, the heat source is located inside the vessel, which causes a temperature gradient along the thickness, especially when the thickness is large. In this case, secondary stress should be considered and thermal ratcheting should be checked. In this paper, a thin-walled ellipsoidal head with heating spiral was studied. In this structure, temperature is uniformly distributed along the thickness but changes alternately between hot and cold along the meridional direction. This has a significant effect not only on the head itself but also on the nozzle. For the nozzle, its elastic support condition has been changed and then its stress distribution will also be changed. In this paper, several cases have been calculated and some laws are established. Finally, some useful conclusions and suggestions are proposed for engineering design.

Thermal stress analysis and study of valves

Simulation and analysis of dynamic heat transfer inside a cryogenic valve under cryogenic test

Thermo-mechanical Stress Analysis of Feed-Water Valves in Nuclear Power Plants

Research on Fluid Dynamics and Thermal Characteristics in Hydraulic Valves by Thermal-Fluid-Solid Coupling Method

The Temperature and Thermal Stress Analysis of Steam Pipe and Correlative Branch Pipe with Finite Element Method

Valve Body’ s Thermal Characteristics Analysis for High-Temperature Electrical Gate Valves and Its Optimal Design

Analysis of the Temperature and Stress Field in a Steam Turbine Bypass Valve Body

Study Of Thermal Stress Distribution On Thick Wall Cylinder By Thermal Shock Treatment

Numerical Study On Temperature Field And Spool Deformation Of Throttle Slide Valve With V-Notches

Analysis of Computers Simulation of ThermalStress in Coking of Shaping Coal

Numerical Simulation of Temperature Field and Stress Field of the Valve Box of a Steam Turbine

Stress-Strain Analysis of Reducing Pipe Under Temperature

TEMPERATURE FIELD AND THERMAL STRESS FINITE ELEMENT ANALYSIS OF A 50MW STEAM TURBINE'S CYLINDER IN A POWER PLANT

Thermal Stress Considered in Design of Jacketed Vessel

Research on Flow Filed and Stress Characteristics of Labyrinth Regulating Valve for Supercritical Thermal Power

Stress analysis of heat exchange tube with inner and outer fins under convection heat transfer conditions

Analysis on Thermal Stress of SV Used in Continuous Casting and Improvement of Its Shape

A Generalized Thermal Deviation Factor to Evaluate the Comprehensive Stress of Tubes under Non-Uniform Heating

THERMAL STRESS ANALYSIS ON WIRE WINDED SUBDIVIDED-COMBINED LARGE EXTRUSION CONTAINER

Fluid-solid-heat Coupling Deformation Analysis of the Valve Trims in a Multistage Pressure Reducing Valve

Stress Analysis of Ellipsoidal Head with Heating Spiral