Abstract:SiC/h-BN multiphase ceramics were prepared via spark plasma sintering (SPS) with t-BN and SiC nanopowders as raw materials and B2O3 as a sintering additive. The phase composition and microstructure of specimens were characterized by X-ray diffraction and scanning electronic microscopy. The effect of sintering additive content on the sintering behavior, densification, microstructure and mechanical properties of SiC/h-BN multiphase ceramics was investigated. The results show that the addition of B2O3 can effectively increase the density and mechanical properties at a low sintering temperature. Compared to the samples without B2O3 additive, the B2O3 additive is effective to decrease the initial shrinkage temperature, promote the rearrangement of h-BN flake grains and improve the bonding strength between the grains. The density of multiphase ceramics increases, and the mechanical properties firstly increase and then decrease with the increase of sintering additive content. The relative density and mechanical properties of the sample with 5% B2O3 content are better than those of other samples, and the relative density, flexural strength, fracture toughness and elastic modulus are 96.92%, 274.7 MPa, 2.91 MPa·m1/2 and 127.2 GPa, respectively. However, the excessive addition of B2O3 is not conducive to the improvement of mechanical properties.

Effect of Si/C Ratio and Their Content on the Microstructure and Properties of Si–B–C–N Ceramics Prepared by Spark Plasma Sintering Techniques

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

The Effect of SiC Content on Microstructure and Microwave Heating Rate of h-BN/SiC Ceramics Fabricated by Spark Plasma Sintering

Microstructures and properties of SiB0.5C1.5N0.5 ceramics consolidated by mechanical alloying and hot pressing

Effect of B2O3 Addition on Low-temperature Sintering Behavior and Properties of SiC/h-BN Multiphase Ceramics

Microstructural Features and Properties of the Nano-Crystalline SiC/BN(C) Composite Ceramic Prepared from the Mechanically Alloyed SiBCN Powder

The Effect of Si Contents on the Reaction-Bonded Si3N4/SiC Composite Ceramics

The Effect of CNTs on the Spark Plasma Sintering Densification Behavior and Mechanical Properties of B4C-Si Powders

Effect of the SiC powder microscopic morphology on properties of Si/SiC ceramics prepared by spark plasma sintering

Influence of Silicon Addition on the Sintering Behavior and Mechanical Properties of Boron Carbide by SPS Process

Microstructure and high-temperature properties of SI-B-C-N MA-powders and ceramic

Effect of SiC Particle Size Distribution on Si3N4/SiC Composite Ceramics

Effect of Sintering Temperature on Structure of C-B4C-SiC Composites with Silicon Additive

Effect of B<sub>4</sub>C on the Mechanical Properties and Microstructure of ZrB<sub>2</sub>-SiC Based Ceramics

Studies of microstructure and mechanical properties of SiC/B4C composites based on reaction sintering

Effect of Initial Phase Composition on the Phase Composition, Microstructure, and Mechanical Properties of Si3N4 Ceramics

Microstructures and Mechanical Properties of SiBCNAl Ceramics Produced by Mechanical Alloying and Subsequent Hot Pressing

Microstructure and mechanical properties of spark plasma sintered SiC ceramics aided by B4C

Microstructure and thermal stabilities in various atmospheres of SiB0.5C1.5N0.5 nano-sized powders fabricated by mechanical alloying technique