Abstract:ABSTRACTPoly(siloxane‐ether‐urethane)‐acrylic (PU‐AC) hybrid emulsions were prepared by introducing different hydroxyethoxypropyl‐terminated polydimethylsiloxane (PDMS) content into the acrylic‐terminated poly(ether‐urethane) backbone and then in situ copolymerizing with methyl methacrylate and butyl acrylate via emulsion process. The effects of PDMS on the particle size and viscoelastic behavior of the hybrid emulsions were investigated. Meanwhile, the hydrogen bonding, mechanical and thermal mechanical properties, water resistance, the surface gloss, and wettability of the resultant hybrid films were also studied. The results showed that all the hybrid emulsions showed shear‐thinning behaviors, and the introduction of PDMS resulted in the formation of the hybrid emulsions with increased average particle size and decreased viscosity. The chemical bonds built between PU and AC yielded higher than 73% crosslinking fraction in all the hybrid materials, but this value decreased with increasing PDMS content because PDMS reduced the hydrogen bonding interactions and enhanced the phase separation. As a result, an increase in the PDMS content led to an increase in the elongation, water resistance, surface roughness, and water hydrophobic of the films, but the tensile strength, hardness, storage modulus, and glass transitions temperature decreased. It is suggested that introduction of PDMS can provide the hybrid materials with the improved flexibility, water resistance, and surface hydrophobicity, which has potential application value in the fouling‐release coatings, biomaterials, and surface fishing. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44927.

Characterization of Poly(2-Hydroxyethyl Methacrylate-Silica) Hybrid Materials with Different Silica Contents

Silica/polyimide Hybrids and Their Dielectric Properties. I. Preparation with an Improved Sol–gel Process with Poly(amic Acid) As the Precursor

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Characterization and Properties of UV‐curable Polyurethane‐acrylate/silica Hybrid Materials Prepared by the Sol‐gel Process

Mechanical Properties of Interface‐free Polyacrylate‐silica Hybrid Sol–gel Materials for Potential Dental Applications

Study of novel low-κ mesoporous silica/PMMA hybrid materials

Acrylic‐Based Polyurethane/Silica Hybrids Prepared by Acid‐Catalyzed Sol–Gel Process: Structure and Mechanical Properties

Study on Poly(butyl Methacrylate)/silica-Titania Hybrid Materials

Hydroxyl Derived the Preparation and Film Formation of Poly(Styrene-co-Acrylate)/Silica Hybrid Emulsion

Sol–gel Derived Composites from Poly(silicic Acid) and 2-Hydroxyethylmethacrylate: Thermal, Physical and Morphological Properties

Comparative Study on Morphology and Properties of Polyimide/silica Hybrid Films Derived from Different Polymeric Precursors

Mechanical properties of silica–(meth)acrylate hybrid coatings on polycarbonate substrate

Novel Polyimide/Silica Nanohybrids from Water Glass

Effects of Composition and Cure Parameters on the Mechanical and Optical Properties of Silicone/Methacrylate Hybrid Elastomers

High-Performance Silica/Epoxy Resin Hybrid Materials Prepared by In-Suit Sol-Gel Process

Matrix Wettability and Mechanical Properties of Geopolymer Cement-Polydimethylsiloxane (PDMS) Hybrids

Effect of Hybrid Hollow Microspheres on Thermal Insulation Performance and Mechanical Properties of Silicone Rubber Composites

Study of Poly(methyl Methacrylate-Maleic Anhydride)/silica Hybrid Materials

Chemical Structure of Composites Derived from Poly(silicic Acid) and 2‐Hydroxyethylmethacrylate

Enhancing Rheological Properties Of Hydrophobically Associative Polyacrylamide Aqueous Solutions By Hybriding With Silica Nanoparticles

Preparation and Properties of Poly(siloxane‐ether‐urethane)‐acrylic Hybrid Emulsions