Abstract:Objective: In this study, new dimethacrylate monomer SiMA without Bisphenol A (BPA) structure was synthesized and used as base resin of dental composite materials with the aim of reducing human exposure to BPA derivatives. Methods: SiMA was synthesized through ring-opening addition reaction between 1,3-bis[2(3,4-epoxycyclohex-1-yl)ethyl]tetra-methyldisiloxane and methacrylic acid, and its structure was confirmed by FT-IR and (1)H NMR spectra. SiMA was mixed with TEGDMA (50/50, wt/wt) and photoinitiation system (0.7 wt% of CQ and 0.7 wt% of DMAEMA) to form resin system. Experimental composite EC was then prepared by SiMA based resin loading with BaAlSiO2 microfillers (72wt%). Double bond conversion (DC) was determined by FT-IR analysis. Volume shrinkage (VS) was measured through variation of density before and after irradiation. Water sorption (WS) and solubility (SL) were obtained until the mass variation of polymer in distilled water kept stable. Flexural strength (FS) and modulus (FM) of the polymer were measured using a three-point bending set up. Extract of composite was used to evaluate its cytotoxic effect on humane dental pulp cells, and relative growth rate (RGR) was obtained by CCK-8 assay. Bis-GMA/TEGDMA (50/50, wt/wt) resin system and universal dental restorative materials 3M ESPE Filtek™ Z250 were used as references for neat resin system and composite material, respectively. Results: FT-IR and (1)H NMR spectra showed that structure of SiMA was the same as designed. For the neat resin systems: DC of SiMA based resin was higher than that of Bis-GMA based resin (p<0.05); SiMA based resin had lower VS than Bis-GMA based resin; WS of SiMA based resin was lower than that of Bis-GMA based resin (p<0.05), while SL of SiMA based resin was nearly the same as that of Bis-GMA based resin (p>0.05); FS and FM of SiMA based resin were lower than those of Bis-GMA based resin (p<0.05). For the composite materials: DC of EC was higher than that of Z250 (p<0.05); EC and Z250 had same VS; WS of EC was lower than that of Z250 (p<0.05), and SL of EC was higher than that of Z250 (p<0.05); FS and FM of EC were lower than those of Z250 (p<0.05); RGRs of EC were lower than those of Z250 after the cells were incubated with relative extract for 24h and 48h (p<0.05), while after being incubated for 72 h, RGR of EC and Z250 had no obvious difference (p>0.05). Significance: SiMA had potential to replace Bis-GMA as base resin of dental composite materials. However, formulation of SiMA based resin and composite should be optimized in terms of mechanical strength to satisfy the requirements of resin based dental materials for clinical application.

Mechanical Properties of Interface‐free Polyacrylate‐silica Hybrid Sol–gel Materials for Potential Dental Applications

Development of Methacrylate/Silorane Hybrid Monomer System: Relationship Between Photopolymerization Behavior and Dynamic Mechanical Properties

Sol–gel Derived Composites from Poly(silicic Acid) and 2-Hydroxyethylmethacrylate: Thermal, Physical and Morphological Properties

Characterization of Poly(2-Hydroxyethyl Methacrylate-Silica) Hybrid Materials with Different Silica Contents

Effect of polyhedral oligomeric silsesquioxane on water sorption and surface property of Bis-GMA/TEGDMa composites

Acrylic‐Based Polyurethane/Silica Hybrids Prepared by Acid‐Catalyzed Sol–Gel Process: Structure and Mechanical Properties

Organic–inorganic Hybrids Derived from 2-Hydroxyethylmethacrylate and (3-Methacryloyloxypropyl)trimethoxysilane

Effect of Silica Nanospheres Silanized by Functional Silanes on the Physicochemical and Mechanical Properties of Bis-GMA/TEGDMA Dental Composite Resin by Photocuring Synthesis

Characterization and Properties of UV‐curable Polyurethane‐acrylate/silica Hybrid Materials Prepared by the Sol‐gel Process

Engineering Interfacial Integrity with Hydrolytic-Resistant, Self-Reinforcing Dentin Adhesive

PROPERTIES OF METHACRYL POLYHEDRAL OLIGOMERIC SILSESQUIOXANE (POSS-MA) DOPED METHACRYLATE-BASED DENTAL RESINS AND COMPOSITES CONTAINING GLASS FLAKE/Ba-Al-SiO2 GLASS POWDER AS INORGANIC DENTAL FILLERS

Synthesis of none Bisphenol A structure dimethacrylate monomer and characterization for dental composite applications

Mechanical properties of silica–(meth)acrylate hybrid coatings on polycarbonate substrate

Poly(methyl Methacrylate) Grafted Silica Nanoparitcles Via ATRP for Bis-GMA/TEGDMA Dental Restorative Composite Resins

New organosilicon maxillofacial prosthetic materials

Structure–property Behavior of UV‐curable Polyepoxy–acrylate Hybrid Materials Prepared Via Sol–gel Process

In-situ sol-gel process for the formulation of Bis-GMA/TEGDMA/silica dental nanocomposite

Preparation and Characterization of Silane-Modified SiO2 Particles Reinforced Resin Composites with Fluorinated Acrylate Polymer.

Study on fluoro-acrylate polymer/SiO2 hybrids prepared by sol-gel process

Synthesis, Characterization and Thermal Properties of Some Organic-inorganic Hybrid Composites

Study of Poly(methyl Methacrylate-Maleic Anhydride)/silica Hybrid Materials