Abstract:Purpose This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved. Design/methodology/approach In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS 2 and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2 and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel. Findings The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss. Originality/value The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Study on the Tribological Characteristics of Solid Lubricants Embedded Tin‐bronze Bearings

Tribological characteristics of solid-lubricant embedded Tin-bronze bearings

A Comparative Investigation of the Tribological Behavior and Wear Mechanism of Bronze-graphite Composite under Dry- and Water-lubricated Sliding Against Steel

Tribological Performance of Graphite Containing Tin Lead Bronze–steel Bimetal under Reciprocal Sliding Test

Study on the Tribological Performance of Tin Bronze-Steel Bimetal Solid Self-lubricating Composites

Study on Friction and Wear Properties of New Self-Lubricating Bearing Materials

Lubrication mechanism of copper-based solid self-lubricating materials by lead

Study on the Tribological Properties and Fault Mechanisms of Copper-Based Alloy Journal Bearing under Different Working Conditions

Investigation of Dry Sliding Friction Wear Behavior of CuSn11 Bronze Plain Bearing Applying Impregnated Graphite-Filled PTFE

The Effect of Solid-Liquid Composite Lubrication on the Tribological Properties of Bearing Steel

The Tribological Characteristics Of Js Material Under Lubrication Of Oil

Experimental Investigation of Tribological Performance of Ptfe-Derived Solid Lubricants in Sliding Building Bearings

Study on the Tribological Performance of Copper-Based Powder Metallurgical Friction Materials with Cu-Coated or Uncoated Graphite Particles as Lubricants

Micro-tribological characteristics of bronze-steel bimetal containing graphite

Effects of Lubricants on Friction and Wear of Ti(Cn)/1045 Steel Sliding Pairs

Wear Behavior of Bronze vs. 100Cr6 Friction Pairs under Different Lubrication Conditions for Bearing Applications

Study on the tribological performance of self-lubricating thrust ball bearings with different embedded features

Effect of composite solid lubricant coatings on the tribological performance of thrust cylindrical roller bearings

Impact of lubrication on the tribological behaviour of PTFE composites for guide rings application

Analysis of the lubrication process with composition of solid lubricants of laser-modified sliding surfaces

Study on Tribological Behavior of Bronze Matrix Self-lubricating Composites