Abstract:Purpose This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved. Design/methodology/approach In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS 2 and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2 and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel. Findings The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss. Originality/value The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Analysis of the lubrication process with composition of solid lubricants of laser-modified sliding surfaces

Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact

Laser irradiation-induced laminated graphene/MoS2 composites with synergistically improved tribological properties

Tribological Properties of Groove-Textured Ti-6Al-4V Alloys with Solid Lubricants in Dry Sliding against GCr15 Steel Balls

Combining Carbon Nanoparticle Coatings and Laser Surface Texturing for Enhanced Lubricity Under High Loads

The Effect of Solid-Liquid Composite Lubrication on the Tribological Properties of Bearing Steel

Graphene-induced reconstruction of the sliding interface assisting the improved lubricity of various tribo-couples

Tribological behavior and microstructural evolution of lubricating film of silver matrix self-lubricating nanocomposite

Effect of composite solid lubricant coatings on the tribological performance of thrust cylindrical roller bearings

Preparation and tribological properties of multi-layer graphene/silicon dioxide composites-based solid lubricant coatings at elevated temperatures

Surface analysis of iron-based self-lubricating composite under oil lubrication

In-Situ Observation and Discrete Element Simulation of Solid Graphite Lubrication Mechanism

Nanostructured tribolayer-dependent lubricity of graphene and modified graphene nanoflakes on sliding steel surfaces in humid air

Tribofilm Formation and Friction Reduction Performance on Laser-Textured Surface with Micro-Grooved Structures

Tribological Performance of Nanocomposite Carbon Lubricant Additive

Strengthening mechanism of different morphologies of nano-sized MSH on tribological performance of phosphate/MoS2 bonded solid lubricating coatings

Effects of Curved Microchannel Surfaces with Sn-Ag-Cu and MXene-Ti3C2 on Tribological Performance of M50 Bearing Steel in Solid–Liquid Composite Lubrication System

Tribological properties and lubrication mechanism of in situ graphene-nickel matrix composite impregnated with lubricating oil

Tribological Properties of Al2O3/Graphite-Al2O3 Laminated Composites under Water Lubrication Conditions

Research on friction and wear behaviors of different solid lubricant coatings on aluminum-based piston skirts

Influence of different loads and temperatures on solid lubricant-filled micro-dimples existing on both cylinder liner and piston ring