Abstract:Bioactive apatite, such as hydroxyapatite ceramic (HA), [Ca10(PO4)6(OH)2] has been extensively investigated for biomedical applications due to its excellent biocompatibility and tissue bioactivity properties. Its bioactivity provides direct bonding to the bone tissue. Because of its similarity in chemical composition to the inorganic matrix of bone, HA is widely used as implant materials for bone. Unfortunately, because of its poor mechanical properties,. this bioactive material is not suitable for load bearing applications. In this study, by the assistance of dip-coating technique, HA coatings were deposited on titanium alloy substrates by employing hydrothermal derived HA powder. The produced coatings then were oven-dried at 130°C for 1 hour and calcined at various temperature over the range of 200-800°C for 1 hour. XRD measurement showed that HA was the only phase present in the coatings. However coatings calcined at 800°C comprised a mixture of HA and tri-calcium phosphate (TCP). FTIR measurement showed the existence of hydroxyl, phosphate, and carbonate bands. PO4 - band became sharper and narrower with the increased of calcination temperature. FESEM observation showed that the coating is polycrystalline with individual particles of nano to submicron size and has an average particle size of 35 nm. The thickness of the coating are direcly propotional with the viscosity of coating slurry. It was shown that the more viscous coating slurry would produce a thicker ceramic coating. Mechanical properties of the coating were measured in term of adhesion strength using a Micro Materials Nano Test microscratch testing machine. The result revealed that the coating had a good adhesion to the titanium alloy substrate.

Hydroxyapatite coating on Ti6Al4V alloy using a sol–gel derived precursor

Hydroxyapatite Coating On Ti6a14v Alloy Using A Sol-Gel Derived Precursor

Synthesis and Charaterization of Silicon-Substituted Hydroxyapatite Coating by Electrochemical Deposition on Ti Substrate

A Novel Method to Synthesize Hydroxyapatite Coating with Hierarchical Structure

Synthesized Silicon-Substituted Hydroxyapatite Coating on Titanium Substrate by Electrochemical Deposition

[Experimental Study of Fast Formation of Biomimetic Apatite Coatings on Pure Titanium Surface].

Preparation and characterization of hydroxyapatite coatings on Ti6Al4V alloy by a sol-gel method

[Fast Formation of Biomimetic Apatite Coatings on Pure Porous Titanium Implant's Surface].

Characterization of eggshell-derived hydroxyapatite on Ti6Al4V metal substrate coated by sol–gel method

Fast deposition of hydroxyapatite coating on titanium alloy by a two-step acid-alkali treatment

Characterization of Hydroxyapatite and Titanium Coatings Sputtered on Ti-6Al-4V Substrate.

Hydroxyapatite Coating with Strong (002) Crystallographic Texture Deposited by Micro-Plasma Spraying

An Interfacial Study of Sol–gel-Derived Magnesium Apatite Coatings on Ti6Al4V Substrates

Development of Bioactive Ceramic Coating on Titanium Alloy substrate for Biomedical Application Using Dip Coating Method

Hydrothermal treatment of Ti surface to enhance the formation of low crystalline hydroxyl carbonate apatite

Direct growth of structurally controllable hydroxyapatite coating on Ti-6Al-4V through a rapid hydrothermal synthesis

Electrohydrodynamic Coating of Metal with Nano-Sized Hydroxyapatite.

Sol–gel derived porous hydroxyapatite coatings

Use of the Sol–Gel Method for the Preparation of Coatings of Titanium Substrates with Hydroxyapatite for Biomedical Application

Biocompatibility and Corrosion Protection Behaviour of Hydroxyapatite Sol-Gel-Derived Coatings on Ti6Al4V Alloy

Hydroxyapatite based on Abalone Mussel Shells Coating on Titanium Alloy using Electrophoretic Deposition Dip Coating as a Bone Implant Candidate