Abstract:Bioactive apatite, such as hydroxyapatite ceramic (HA), [Ca10(PO4)6(OH)2] has been extensively investigated for biomedical applications due to its excellent biocompatibility and tissue bioactivity properties. Its bioactivity provides direct bonding to the bone tissue. Because of its similarity in chemical composition to the inorganic matrix of bone, HA is widely used as implant materials for bone. Unfortunately, because of its poor mechanical properties,. this bioactive material is not suitable for load bearing applications. In this study, by the assistance of dip-coating technique, HA coatings were deposited on titanium alloy substrates by employing hydrothermal derived HA powder. The produced coatings then were oven-dried at 130°C for 1 hour and calcined at various temperature over the range of 200-800°C for 1 hour. XRD measurement showed that HA was the only phase present in the coatings. However coatings calcined at 800°C comprised a mixture of HA and tri-calcium phosphate (TCP). FTIR measurement showed the existence of hydroxyl, phosphate, and carbonate bands. PO4 - band became sharper and narrower with the increased of calcination temperature. FESEM observation showed that the coating is polycrystalline with individual particles of nano to submicron size and has an average particle size of 35 nm. The thickness of the coating are direcly propotional with the viscosity of coating slurry. It was shown that the more viscous coating slurry would produce a thicker ceramic coating. Mechanical properties of the coating were measured in term of adhesion strength using a Micro Materials Nano Test microscratch testing machine. The result revealed that the coating had a good adhesion to the titanium alloy substrate.

An Interfacial Study of Sol–gel-Derived Magnesium Apatite Coatings on Ti6Al4V Substrates

Electrolytic Deposition of Magnesium-Substituted Hydroxyapatite Crystals on Titanium Substrate

Synthesis and Charaterization of Silicon-Substituted Hydroxyapatite Coating by Electrochemical Deposition on Ti Substrate

Evolution of the magnesium incorporated amorphous calcium phosphate to nano-crystallized hydroxyapatite in alkaline solution

Apatite deposition on thermally and anodically oxidized titanium surfaces in a simulated body fluid.

In Vitro Effect of Magnesium Inclusion in Sol–gel Derived Apatite

[Experimental Study of Fast Formation of Biomimetic Apatite Coatings on Pure Titanium Surface].

Osteoblastic Cell Response on Magnesium-Incorporated Apatite Coatings

Hydroxyapatite coating on Ti6Al4V alloy using a sol–gel derived precursor

Longer-Term Mechanical And Biological Evaluation Of Titanium Alloy Coated With Apatite Layer

Hydroxyapatite Coating On Ti6a14v Alloy Using A Sol-Gel Derived Precursor

Interfacial Study of Magnesium-Containing Fluoridated Hydroxyapatite Coatings

Improvement of bioactivity with magnesium and fluorine ions incorporated hydroxyapatite coatings via sol–gel deposition on Ti6Al4V alloys

TiSZ-reinforced hydroxyapatite coatings on magnesium substrate with titanium interlayer

Preparation and characterization of hydroxyapatite coatings on Ti6Al4V alloy by a sol-gel method

[Fast Formation of Biomimetic Apatite Coatings on Pure Porous Titanium Implant's Surface].

Characterization of Hydroxyapatite and Titanium Coatings Sputtered on Ti-6Al-4V Substrate.

Highly adhesive hydroxyapatite coatings on titanium alloy formed by ion beam assisted deposition

Effect of Nanostructured Surface of Light Metals on Hydroxyapatite Coating

Development of Bioactive Ceramic Coating on Titanium Alloy substrate for Biomedical Application Using Dip Coating Method

Effect of Reaction Temperature on the Microstructure and Properties of Magnesium Phosphate Chemical Conversion Coatings on Titanium