Abstract:Titanium alloys are known for being difficult to machine. Within the groups of Ti alloys, the machinability is reduced when going from the α-alloys, to α + β, and finally to near-β or β-alloys. Uncoated cemented carbide is traditionally used for machining these alloys and finding a suitable coating to improve the performance is a challenge due to the high strength of Ti alloys and the high chemical reactivity of Ti with tool and coating materials at the temperatures achieved during cutting. The PVD applied Ti x Al 1-x N (x = 0.4–0.7) is generally recommended for machining Ti alloys and a top layer of NbN has shown promising performance in milling applications. This study systematically explores the wear mechanisms of either uncoated WC-12%Co or its Ti 0.45 Al 0.55 N-NbN coated version in the milling of Ti alloys ranging from near-α (Ti-6Al-2Sn-4Zr-2Mo), α + β (Ti-6Al-2Sn-4Zr-6Mo), and near-β (Ti-5Al-5Mo-5 V-3Cr) alloys. The wear evolution is explored by studying as-worn tools and their cross-section using SEM-XEDS and EBSD after having reached 10%, 30%, 50%, and 100% of the full tool life at a flank wear criterion VB = 200 μm. The coating is removed within seconds of engagement and fails by cracking within the bulk and PVD droplet defects can initiate such cracks. Diffusional dissolution of the coating may be active on a minor scale, but the rapid mechanical failure shows the need for a more robust coating formulation. Exposed cemented carbide is worn at varying intensities when machining the Ti alloys. The highest wear rate is achieved in milling α + β Ti-6246, followed by a moderate wear rate in near-β Ti-5553, and with a slower wear rate in milling near-α Ti-6242 which is explained varying intensities in oxidation wear, diffusional dissolution, and mechanical cracking. Diffusional loss of C gives rounder WC grains and remaining W at the interface is removed by the chip flow. Diffusional loss of Co gives reduced grain bonding and loss of the dampening effect that leads to fractures in WC grains. Specifically in milling α + β Ti-6246 and in minor scale in near-α Ti-6242, there is formation of CoWO 4 ceramic present several μm into the tool and its formation is facilitated by the oxidation of binder with resolved W. Fractures within the CoWO 4 explains the high wear rate. Cracks also propagate in binder regions initiated from weakened interface regions due to diffusional loss of C and Co.

Behavior of Ti Coating in CBN/Ti/Vitrified Bond Gradient Materials

Study on the Performance of CBN Abrasives with Ti Coatings

Interface Bonding Between Ti-Coated CBN and Vitrified Bond

Microstructure, mechanical properties and cutting performance of super-hard Ti(B,C,N) coatings prepared by chemical vapor deposition method

Oxidation Behavior of Ti–B–C–N Coatings Deposited by Reactive Magnetron Sputtering

Study on the growth and wear characters of CVD coating deposited on Ti(C, N)-based cermets with adding different C/N ratios of Ti(C, N) powders

Tribological behavior at elevated temperature of multilayer TiCN/TiC/TiN hard coatings produced by chemical vapor deposition

High-Speed Rubbing Behavior of Abrasive Coating Coated on Titanium Alloy Blade Tips

High Temperature Decomposition Behavior of CaZrO3 Coating on Graphite for TiNi Alloy Melting

Influence of TiO2 amount on the interfacial wettability and relevant properties of vitrified bond CBN composites

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Understanding wear mechanisms of TiSiCN/Zr(C)N coatings at elevated temperatures

Growth behavior of CVD Ti(C,N,O) coating on cemented carbide controlled by CO and the mechanism

Microstructure and Mechanical Properties of TiC-Fe Surface Gradient Coating on a Pure Titanium Substrate Prepared in Situ

Corrosion and Wear Properties of h-BN Modified TC4 Titanium Alloy Micro-Arc Oxide Coatings

MT-CVD Ti(C,N,O) coatings controlled by CO: Microstructure evolution and its effect on the hardness

Friction and wear behaviors of TiCN coating based on electrical discharge coating

Elevated-temperature Tribological Behavior of Ti–B–C–N Coatings Deposited by Reactive Magnetron Sputtering

Study of the Properties and Application of Ti-Coated Diamond by Measuring Resistance

Residual stress and ablation behavior of CVD TaC coatings on graphite

Preparation, Mechanical Properties and Cyclic Oxidation Behavior of the Nanostructured NiCrCoAlY-TiB2 Coating