Abstract:The relationship among raw materials used, processing conditions, the resulting morphology, and mechanical properties were studied for unidirectional (1D), bidirectional (D) and tridirectional (3D) carbon-carbon composites. Experimental results demonstrated that an increased number of densifications and higher composite densities were associated with elevated strength properties. Generally, tensile and flexural properties were found to be fiber-dominated, whereas compression behavior was mainly affected by density and matrix morphologies. Tensile moduli of 1D and 3D composites were found to be higher than values calculated according to the fibers' content. This was attributed to the contribution of the sheath matrix morphology. Tensile strength levels were significantly lower than expected because of residual stresses resulting from thermal processing. With respect to matrix effects, measured properties indicated that high glass-like carbon fraction resulted in enhanced strength and modulus, both in tension and compression. Microstructure observations indicated that higher matrix packing density contributed to this result. Pitches containing heavy fractions gave rise to increased compression strength, whereas light fraction types of pitches displayed higher tensile strength, because of different matrix morphologies in each case. Atmospheric pressure carbonization of 3D composites resulted in void-containing matrix with almost no sheath morphology. Consequently, the associated mechanical properties were inferior. Distinctively, atmospheric pressure carbonization of 1D and 2D composites is quite effective in sheath morphology formation. Consequently, mechanical properties are only slightly inferior to those of the high-pressure densified composites. Finally, it was observed that graphitization tended to reduce strength and enhance modulus, compared to only carbonized composites. Non-sequentially graphitized 3D composites are disadvantageous, compared with composites graphitized following each densification. The duration of graphitization tended to reduce compression strength with longer processes.

Preparation and Mechanical Properties of Carbon/carbon Composites with High Textured Pyrolytic Carbon Matrix

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Mechanical and thermal conduction properties of carbon/carbon composites with different carbon matrix microstructures

Epitaxial Grown Carbon Nanotubes Reinforced Pyrocarbon Matrix in C/C Composites with Improved Mechanical Properties

Preparation, microstructure and properties of three-dimensional carbon/carbon composites withhigh thermal conductivity

Reinforcement of C/C materials prepregs with pyrocarbon coated carbon fiber as the way to improve the prepregs properties after pyrolysis

Effect of pyrocarbon interphase texture and thickness on tensile damage and fracture in T‐700TM carbon fiber–reinforced silicon carbide minicomposites

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers

Influence of pyrolytic carbon interphase and pyrolysis temperature on the mechanical and tribological properties of Cf/SiC after heat treatment at 1800 °C

Effects of pyrochemical treatment for producing interfacial carbon layer on tensile properties of polymer-derived-matrix-based SiC/SiC composites

Effect of carbon matrix on mechanical and tribological properties of Cf/Cu/C composites

Microstructure, Thermophysical Property and Ablation Behavior of High Thermal Conductivity Carbon/carbon Composites after Heat-Treatment

The effect of carbon nanotubes on the microstructure and morphology of pyrolytic carbon matrices of C–C composites obtained by CVI

Effect of pyrolytic carbon interphase on mechanical properties of mini T800-C/SiC composites

Correlation of the permeability and porosity development of carbon/carbon composites during pyrolysis

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method

PyC interphase growth mechanism and control models of C/SiC composites

Effect of materials and processing on the mechanical properties of C/C composites

Study on the Preparation and Process Parameter-Mechanical Property Relationships of Carbon Fiber Fabric Reinforced Poly(Ether Ether Ketone) Thermoplastic Composites

Improving carbon/carbon composites mechanical and thermal properties by the co‐carbonization of pre‐oxidized carbon fiber and pitch

Mechanical properties of C/C composites processed by wet impregnation and P-CVI methods