Abstract:Carbonization is the first step in the heat and pressure treatment (pyrolysis) of composites in preparing carbon-carbon parts. These find many uses, including aircraft brakes, rocket nozzles and medical implants. This paper describes the acoustic emissions (AE) from various stages of the manufacturing process of carbon-carbon composites. This process involves carbonization at a high temperature and this results in both thermal expansion and volume change (due to pyrolysis in which a sacrificial polymer matrix is converted to carbon). Importantly the resultant matrix is porous and has a network of small intra-lamina cracks. The formation of these microcracks produces AE and this paper describes how this observation can be used to monitor (and eventually control) the manufacturing process. The aim is to speed up manufacture, which is currently time-consuming. The first section of the paper describes the design of unimodal waveguides to enable the AE to propagate to a cool environment where a transducer can be located. The second part of the paper describes various experimental observations of AE under a range of process conditions. In particular, this paper presents a technique based on detecting acoustic emissions and (1) uses wire waveguides to monitor parts within the autoclave to 800 degrees C, (2) monitors microcracking during pyrolysis, (3) uses a four-level threshold to distinguish between low- and high-amplitude cracking events, (4) recognizes the occurrence of harmful delaminations, and (5) guides the control of the heating rate for optimum efficiency of the pyrolysis process. In addition, supporting data are presented of in situ measurements of porosity, weight loss, cross-ply shrinkage, and mass spectroscopy of gases emitted. The process evolution is illustrated by the use of interrupted manufacturing cycle micrographs obtained by optical, scanning acoustic (SAM) and scanning electron (SEM) microscopy. The technique promotes in-process monitoring and control but also contributes to current understanding of pyrolysis.

Correlation of the permeability and porosity development of carbon/carbon composites during pyrolysis

Comparison of the in situ compressive behavior of carbon fibers woven ply laminates exposed to one‐sided heat flux: Thermoplastic versus thermosetting composites

Reinforcement of C/C materials prepregs with pyrocarbon coated carbon fiber as the way to improve the prepregs properties after pyrolysis

Pyrolysis behavior of the nanoporous phenolic matrix and the resultant microstructure and property evolution in the composites

Recovery of Carbon Fibre from Waste Prepreg via Microwave Pyrolysis

Evolution of pyrolysis char during the recovery of carbon fiber reinforced polymer composite and its effects on the recovered carbon fiber

Acoustic emission technique for monitoring the pyrolysis of composites for process control

Modeling the pyrolysis of 3D-printed tannin-based composites – A first approach

Effects of Pyrolysis Temperature on Characteristics of Porosity in Biomass Chars

Pyrolysis Behavior, Pyrolysis Kinetics, Heat Transfer and Pyrolysis Simulation of Almandine/Boron Phenolic Resin Ceramizable Composites

Experimental Permeability and Porosity Determination of All-Oxide Ceramic Matrix Composite Material

A review on gas permeability of polymer matrix composites for cryogenic applications

Microstructure and mechanical properties of 3D Cf/SiBCN composites fabricated by polymer infiltration and pyrolysis

Pretreating Recycled Carbon Fiber Nonwoven with a Sizing Formulation to Improve the Performance of Thermoplastic Recycled Fiber-Reinforced Composites

Effects of pyrochemical treatment for producing interfacial carbon layer on tensile properties of polymer-derived-matrix-based SiC/SiC composites

Microstructure Evolution and Its Correlation with Performance in Nitrogen-Containing Porous Carbon Prepared by Polypyrrole Carbonization: Insights from Hybrid Calculations

Direct observation of the morphological changes in a carbon fiber composite by means of in-situ micro-CT compression experiment

Thermal decomposition study of carbon fiber-reinforced polyphenylene sulfide at high heating rates met under fire exposure

Effect of pyrocarbon interphase texture and thickness on tensile damage and fracture in T‐700TM carbon fiber–reinforced silicon carbide minicomposites

Discrete Element Simulation of Transverse Cracking During the Pyrolysis of Carbon Fibre Reinforced Plastics to Carbon/Carbon Composites

Preparation and Properties of Porous SiC/SiC Composites