Abstract:This work is aimed at studying the foaming behavior of polypropylene (PP) with supercritical carbon dioxide (scCO2). The effects of saturation time, foaming temperature, saturation pressure and depressurization rate on the foam structure and volume expansion ratio were investigated. A likely foaming zone delimited by the upper and lower limits for foaming temperature and saturation pressure was determined. The upper limit for foaming was dictated by the melt strength of the PP while the lower one by the deformability of the PP. The maximum likely foaming temperature range was very narrow, only about 4°C, whatever the saturation pressure, showing the poor foamability of PP. There was a sort of equivalence between increasing foaming temperature and increasing saturation pressure in terms of the foamability. However, a lower foaming temperature and a higher saturation pressure were more favorable for obtaining uniform foam than a higher foaming temperature and a lower saturation pressure. At given foaming temperature and saturation pressure, increasing depressurization rate led to an increase in cell density. However, both the cell size and the foam volume expansion ratio first increased with increasing depressurization rate, reached a maximum at some point and then decreased with a further increase in depressurization rate.

Constrained Foaming of Polystyrene with Supercritical Carbon Dioxide

Foaming of Polypropylene with Supercritical Carbon Dioxide

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

A Two-Step Depressurization Batch Process for the Formation of Bi-Modal Cell Structure Polystyrene Foams Using Scco2

Controlled Foaming of Polycarbonate/polymethyl Methacrylate Thin Film with Supercritical Carbon Dioxide

Strategy for Preparation of Microcellular Rigid Polyurethane Foams with Uniform Fine Cells and High Expansion Ratio Using Supercritical CO2 As Blowing Agent

Systematic Study of Alcohols Based Co-Blowing Agents for Polystyrene Foaming in Supercritical CO2: Toward the High Efficiency of Foaming Process and Foam Structure Optimization

Effect of Foaming Temperature on Cell Structure of Foamed Polypropylene Using Supercritical CO2

Microcellular Foaming of Polysulfones in Supercritical CO2 and the Effect of Co-Blowing Agent

Second Cell Growth Optimized by Heating Mode During Two-Step Supercritical CO2 Foaming Polymer Process

High Performance Attapulgite/Polypyrrole Nanocomposite Reinforced Polystyrene (PS) Foam Based on Supercritical CO2 Foaming

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Formation Mechanism of Bi-modal Cell Structure Polystyrene Foams by Synergistic Effect of CO2-philic Additive and Co-blowing Agent

Foaming Window for Preparation of Microcellular Rigid Polyurethanes Using Supercritical Carbon Dioxide As Blowing Agent

Application of a CO2 Pressure Swing Saturation Strategy in PP Semi-Solid-State Batch Foaming: Evaluation of Foamability by Experiments and Numerical Simulations

Fabrication of Polystyrene/nano‐caco3 Foams with Unimodal or Bimodal Cell Structure from Extrusion Foaming Using Supercritical Carbon Dioxide

Foaming Behavior of the Fluorinated Ethylene Propylene Copolymer Assisted with Supercritical Carbon Dioxide

Study on Extrusion Foaming of Polypropylene/Polydimethylsiloxane Blends

Key Factors for Regulation of Cell Morphology in Supercritical CO2 Direct Rapid Depressurization Foaming Silicone Rubber Process

A Comparative Study of the Effect of Multidimensional Carbon Fillers on Polystyrene Using Supercritical Carbon Dioxide Foaming

Effects of Crystal Structure on the Foaming of Isotactic Polypropylene Using Supercritical Carbon Dioxide As a Foaming Agent