Abstract:Introduction. Modern conditions of iron and steel making industry require production of high-quality competitive metal products. Thus, the removal of sulfur at the lowest cost has been becoming increasingly important.Problem Statement. The major amount of sulfur in iron and steel making comes with charge materials in sintering blast furnace production. When using out-of-furnace processing of hot metal in hot metal desulfurizationand slag removal facilities, the degree of hot metal desulfurization can be 75—99%. This ensures the production of hot metal with a sulfur content in the range of 0.002—0.015%.Purpose. The analysis of changes in the sulfur content of hot metal and in the slag composition in the processchain of steel production, followed by the development of technical solutions and process methods to eliminate theresulfurization of hot metal.Materials and Methods. Our calculations, based on the actual data of Ukrainian and Chinese iron and steelmaking facilities. The selected samples of slag and hot metal have been analyzed with the use of raster spectralmicroscopy methods. In the studies of sulfur content at various stages of smelting, the method of material balancecalculation has been employed.Results. In the slag phase, along with systems of CaO ∙ SiO2 ∙ Al2O3 type with diff erent ratios of componentscontaining 0.2—3.5% sulfur, CaxSiyAlz type systems containing up to 1% sulfur have been detected. In the beads, the sulfur content varies within 0.1—0.85%. Sulfur is present in the form of sulfi des of (Fe, Mn)S type, mainlyMnS, while in non-metallic inclusions of the beads, the sulfur content ranges within 15—30%. The residing ladleslag after desulfurization should not exceed 0.5—0.7 kg/t of hot metal.Conclusions. To prevent the resulfurization of hot metal during its discharge from a blast furnace, it is advisable to rationalize ladle slag modes, by adjusting ladle slag composition, increasing the degree of ladle cleaning from the slag residing from previous loads and inducing a slag cover in the absence of ladle slag. The conducted studies have shown that sulfur from the slag does not return to the hot metal and resulfurization does not occur, which is explained by the protective eff ect of residual magnesium.

Research on Slag-conglomerating Agent of Pure Magnesium Desulphurization in Hot Metal

Effect of W(mgo)/w(al2o3) Ratio and Basicity on Microstructure and Metallurgical Properties of Blast Furnace Slag

Study on Desulfurization and Denitration of with Industry Solid Waste by Microwave

Hydrometallurgical Leaching Behavior and Kinetic Modeling of Blast Furnace Slag in Hydrochloric Acid

Evaluating the Effect of MgO/Al2O3 Ratio on Thermal Behaviors and Structures of Blast Furnace Slag with Low Carbon Consumption

Research of slagless steelmaking and technology control in converter

Study on Metallurgical Properties of Blast Furnace Slag at YIGANG

Directional sulfur removal from ladle furnace slag by electric field strengthening treatment

High-temperature Modification and Air-Quenching Granulation of Steel Slag

Experiments on effect of red mud-based slag on distribution of sulfur in liquid iron

Desulphurization of Hot Metal and Ferronickel with Calcium Aluminate Fluxes

Study on magnesium reduction process for air-cooled high magnesium-bearing blast furnace slag

Magnetic separation characteristics of steel slag powder in a fluidized dry magnetic network separator

Change in Slag Composition and Sulfur Content of Hot Metal in the Process Chain of Blast Furnace — Hot Metal Desul furization Complex — Converter (BOF)

Effect of highly oxidizing converter dephosphorization slag on dephosphorization behaviour of molten steel

Mass Transfer Model of Desulfurization in the Electroslag Remelting Process

Experimental Study on Deep Desulphurization of Clean Steel in Refining Process

Generation, utilization, and environmental impact of ladle furnace slag: A minor review

A novel synergistic method on potential green and high value-added utilization of blast furnace slag

Dephosphorization in New Double Slag Converter Steelmaking Process with High‐Temperature Laboratorial Experiments

Integrated carbon dioxide/sludge gasification using waste heat from hot slags: syngas production and sulfur dioxide fixation.