Abstract:The chemical-vapor-deposition (CVD) process is sufficiently well developed to allow the large-scale production of carbon nanotubes (CNTs). Metal nanoparticles (Fe, Co, Ni, etc.) are usually immobilized on a solid support and then decompose the gaseous hydrocarbon feedstocks into fragmented carbon units at elevated temperatures of 700-1100°C. Metal carbides are formed and then these dominate the growth of filamentous carbon as a structural template. The produced CNTs cannot stay firmly with an inert support and so inevitably detach away, especially during liquidphase purification or mechanical treatment. The biggest difficulties when handling the loose powder are filtration in the slurry-phase operations and the large pressure drops in fixed-bed reactors. These problems very much limit the application of CNTs on a large scale. The fabrication of carbon filaments on a structured support (e.g., activated carbon, carbon fibers, porous frameworks, graphite) has also suffered from discontinuities in the structure. The future use of CNTs has also been restricted by the technical requirements and the necessary high energy consumption to operate the intense and complicated CVD process. To avoid any mechanical post-treatment of powder and the risk of explosion during CVD synthesis, we have explored a simple method to produce monolithic CNTs directly as millimeter-scale spheres, featuring an integral continuity in the structure from microscopic to macroscopic scales. The whole process of CNTs growth has been conducted in a flow of ultrapure N2, involving a set of elementary steps in the solid phase being less complex than the widely used CVD process. The growth of CNTs is based on a solid reaction mechanism and well-graphitized nanotubes can be obtained even at a temperature as low as 400C. Direct observation of all growth events is made by using in-situ transmission electron microscopy (TEM), X-ray diffraction (XRD), IR, Raman spectroscopy and thermogravimetric analysis. A commercial styrene-divinylbenzene copolymer resin was used as the carbon precursor. According to Scheme 1, the ion-exchanged resin spheres were calcined at 800C in a flow of N2 or vacuum, after which the average diameter decreases from 0.77 to 0.49 mm, while the bulk density increases from 0.55 to 0.91 g ml. A novel macroscopic structure can be clearly seen, especially after the removal of the Fe nanoparticles and the amorphous carbon species by refluxing the spheres in concentrated HNO3. As seen in Fig. 1a, the twisted nanotubes construct the monolith while keeping a spherical shape. The cross-section views of the hand-broken spheres show no difference in the structure between the bulk and the surface, indicating a homogeneous distribution of the nanotubes in the millimeter-scale spheres (Fig. 1b). The nitrogen adsorption/ desorption isotherm shows a hysteresis loop to identify a typical mesoporous feature. The measured BET surface area and the pore volume are 223.7 m g and 0.42 ml g, respectively. The distribution of the pores ranges between about 2 and 15 nm.

Synthesis of Chaoite-Like Macrotubes at Low Temperature and Ambient Pressure

Ferromagnetic Chaoite Macrotubes Prepared at Low Temperature and Pressure

Nanostructured Hybrid Carbon Nanotube/UltraHigh‐Temperature Ceramic Heterostructures: Microstructure Evolution and Forming Mechanism

A Pressure Enhanced Cvd Method for Large Scale Synthesis of Carbon Microtubes and Their Mechanical Properties

Morphology of Carbon Nanotubes Prepared by Carbon Arc

Growth Of High-Quality Single-Wall Carbon Nanotubes Without Amorphous Carbon Formation

The Production of Carbon Microtubes by the Carbonization of Catkins and Their Use in the Oxygen Reduction Reaction

Large‐Scale Synthesis, Annealing, Purification, and Magnetic Properties of Crystalline Helical Carbon Nanotubes with Symmetrical Structures

Structural characterization and electrochemical lithium insertion properties of carbon nanotubes prepared by the catalytic decomposition of methane

Formation of variously shaped carbon nanotubes in carbon dioxide–alkali metal (Li, Na) system

General Oriented Formation of Carbon Nanotubes from Metal-Organic Frameworks.

Spherical Multi-Walled Carbon-Nanotube Architectures : Formation Mechanism and Catalytic Performance

TEM Studies of the Initial Stage Growth and Morphologies of Bamboo-Shaped Carbon Nanotubes Synthesized by CVD

Synthesis of Scroll‐Type Composite Microtubes of Mo2C/MoCO by Controlled Pyrolysis of Mo(CO)6

Fabrication at room temperature of uniform mesopore partially carbonized microtubes via an interface reaction

Preparation and mechanical properties of highly-aligned carbon micro-trees

Synthesis and Magnetic Properties of Aligned Carbon Nanotubes by Microwave-Assisted Pyrolysis of Acetylene

Selective Synthesis of Conjugated Chiral Macrocycles: Sidewall Segments of (−)/(+)‐(12,4) Carbon Nanotubes with Strong Circularly Polarized Luminescence

Large-scale synthesis of 3D ordered microporous carbon at low temperature using cobalt ions exchanged zeolite Y as a template

Low-temperature synthesis of multi-walled carbon nanotubes over Cu catalyst

An experimental study on the hydrothermal preparation of tochilinite nanotubes and tochilinite–serpentine-intergrowth nanotubes from metal particles