Abstract:In this paper, mechanical properties and microstructures of the cast and extruded Al-xCu-1Li-0.4Mg–1Zn-0.1Zr alloys (x = 2.0, 3.0, 4.0, 4.5, 5.5, 6.5 wt%) were investigated. The results showed that the as-cast micrographs of alloys with different Cu content primarily consist of dendritic α-Al grains, and the intermetallic phases at the grain boundaries were Cu and Zr rich phases. After solution treatment, no recrystallization took place in extruded alloys, and the alloys mainly represented mixed textures composed of <111> and <100> fibers. Cu significantly affected the precipitation behavior of the extruded alloys. Only T1 (Al2CuLi) phases were observed in T6 (aging at 175 °C for 32 h) and T8 (3% pre-strain followed by aging at 150 °C for 32 h) treated alloy with 2 wt% Cu. Further increasing Cu contents (4.5 and 6.5 wt%) enabled the co-precipitation of T1 and θ' (Al2Cu) phases, as well as increased their density. In addition, the microstructures of grain boundaries of alloys with different Cu content showed dramatic differences. T1 phases precipitated at the grain boundaries of alloy containing 2 wt% Cu, while rare precipitation of T1 phases was observed at the grain boundaries of alloy with 6.5 wt% Cu. The yield strength (YS) of the alloys increased with the Cu content and the elongation (EL) showed an opposite trend. A good combination of ultra-high strength (YS = 684 MPa, ultimate tensile strength = 726 MPa) and ductility (EL = 6.3%) was obtained in T8 treated alloy containing 4.5 wt% Cu. The presence of the undesired coarse T2 (Al6CuLi3) phases at the grain boundaries resulted in the premature failure of the high Cu content alloys.

The Stored Energy in Processed Cu–0.4 Wt.%cr–0.12 Wt.%zr–0.02 Wt.%si–0.05 Wt.%mg

Thermal Stability of Heavily Drawn Cu–0.4 Wt.%cr–0.12 Wt.%zr–0.02 Wt.%si–0.05 Wt.%mg

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

EFFECT OF HEAVILY DRAWING ON THE MICROSTRUCTURE AND PROPERTIES OF Cu-Cr ALLOYS

Microstructures and properties of cold drawn submicron crystalline Cu-5wt%Cr material

Relating Residual Stress and Microstructure to Mechanical and Giant Magneto-Impedance Properties in Cold-Drawn Co-based Amorphous Microwires

Strain Compatibility Behavior in Cu-6%Ag Alloy During Drawing into Filamentary Structure

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Dislocation Behavior and Strengthening Mechanisms of Cu-Te Alloy Drawn at Room and Cryogenic Temperatures

The effect of cold drawing on the structure, tensile fracture strength and reliability of CuZrAl amorphous microwires

Tensile Deformation and Fracture Behaviours of Cold Rolled Cu-3wt.%Ag-0.5wt.%Zr Thin Sheets with Different Annealed Microstructures

Analysis of Stored Energy in Cold-Rolled Copper Using Bulk and Microstructure-Based Techniques

Microstructure and Stored Energy Evolutions During Rolling of Cu60Zr20Ti20 Bulk Metallic Glass

Effect of drawing deformation on microstructure and mechanical properties of Fe-Cr-Co-W alloy

Effect of Microstructure and Microtexture on the Mechanical Properties of Small-Strain Cold-Drawn Pearlite Steel Wires

Ex-situ EBSD investigation of the reduced c/a values and work hardening behavior in Mg-4Li-1Al-0.5Y alloy under hot compression

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

Microstructure and Properties of High Strength and High Conductivity Cu-0.4Mg Alloy Processed by Upward Continuous Casting and Multi-pass Drawing

Dynamic Compressive Behaviour and Microstructural Evolution of Extrusion-Shear Mg–6Zn–1Cu–1Y–0.6Zr Alloy

Hot Deformation Constitutive Model and Processing Maps of Homogenized Al–5Mg–3Zn–1Cu Alloy