Abstract:AbstractThe search for suitable friction materials for high-speed train is an attractive but difficult problem. In recent years, a variety of different novel friction materials were fabricated to meet the aims of high loads and speeds under ambient environment. Carbon fiber-reinforced carbon composites (C/C), carbon fiber-reinforced silicon carbide composites (C/C-SiC) and metallic composites fabricated by powder metallurgy are three excellent materials among them. Here a comparison of these three different materials working as brake pads, coupled with high-density C/C-SiC brake disk, was described. All the experiments were conducted using the same procedure with increasing initial braking speed (the rotation speed of brake disk at the beginning of braking process) from 30 to 59 m/s and constant load of 1.25 MPa, simulating the real working condition of high-speed train. The coefficient of friction (COF) and wear rates of three materials were compared and analyzed. During experiments, the COF of metallic and C/C pads remains nearly constant at 0.31 and 0.22, respectively, with increasing braking speed, while that of C/C-SiC exhibits a parabola. These different trends of COF may be attributed to the distinctive forming processes of friction film on the top of contact surfaces. Meanwhile, the wear rates of metallic composites increase rapidly from 683 to 1803 mm3/MJ with initial braking speed, while C/C-SiC presents the highest wear loss of 1887 mm3/MJ at 49 m/s and lowest value of 315 mm3/MJ at 59 m/s. Interestingly, the wear rate of C/C composites, due to the appropriate bonding strength of matrix/fiber and relatively high shear stress, decreases from 3698 to 903 mm3/MJ with increasing initial braking speed, which does not consist with pre-existing paper. Thus, metallic pads presented the lowest wear rates at lower speed (<49 m/s) but the highest at high speed, while C/C-SiC composite pads showed the greatest wear resistance at high speed. This investigation of three different friction materials will enhance our understanding of these friction materials and benefit the selection and safe application of high-speed train friction materials.

Study on the Particle-Reinforced Cu-Matrix Brake Pads for 300 Km·h-1 High-Speed Trains

Application Status and Research Progress of Brake Disc Materials for High-speed Train

Effect of Sintering Temperature on the Microstructure and Mechanical and Tribological Properties of Copper Matrix Composite for Brake Pads

Data-driven design of brake pad composites for high-speed trains

Synergistic Effects of Different Graphite on the Braking Performance of Cu-Matrix Friction Materials for High-Speed Trains Based on Pin–Disc Tests

Braking Performance of Fe-Based and Cu-Based Powder Metallurgy Pads Paired with C/C-SiC Disk on Full-Scale Dynamometer

Friction and Wear Mechanics of Fe-Based PM Pad Paired with Carbon Fiber-Reinforced Silicon Carbide (C/C-SiC) Disk Under High-Speed Braking

Comparison of Friction and Wear Behavior Between C/C, C/C-SiC and Metallic Composite Materials

Effects of Aluminosilicate Particles on Tribological Performance and Friction Mechanism of Cu-matrix Pads for High-Speed Trains

Preparation and Dynamometer Tests of 3D Needle‐Punched C/C‐SiC Composites for High‐Speed and Heavy‐Duty Brake Systems

Dry Sliding Wear Studies of Cu-Based Powder Metallurgy Brake Materials

Braking Performance of Copper-Based Friction Materials Reinforced by AlCoCrFeNi High-Entropy Alloy

Comparison of Braking Behaviors Between Iron- and Copper-Based Powder Metallurgy Brake Pads That Used for C/C–SiC Disc

Braking behaviors of Cu-based PM brake pads mating with C/C–SiC and 30CrMnSi steel discs under high-energy braking

Study of Fe and Cu-based P/M friction materials for automotive brake pads

Effect of Surface Modification on the Tribological Properties of Friction Blocks in High-Speed Train Brake Systems

Influence of Braking Conditions on Tribological Performance of Copper-Based Powder Metallurgical Braking Material

Effect of Iron Powder Type on Friction and Wear Properties of Copper-Based Friction Powder Metallurgy Material

Comparison of the Braking Behavior Among Cast Steel, Carbon/Carbon (C/C) and Carbon/Carbon-Silicon Carbide (C/C-SiC) Materials Mated with Copper-Based Composites

Sepiolite: A New Component Suitable for 380 Km/h High-Speed Rail Brake Pads

Friction mechanism analysis of copper-based composites reinforced with ball-milled and modified composite ceramic powders