Abstract:In this study, the friction performance of copper-based (Cu-PM) and iron-based (Fe-PM) powder metallurgy pads was systematically compared and analyzed by performing a braking test paired with a C/C-SiC disk on a full-scale flywheel brake dynamometer, including coefficient of friction (COF), wear rate (Wr), and worn surface under dry and wet tests. The test procedure simulated the braking conditions on high-speed trains with initial brake speeds (IBS) from 50 km/h to 200 km/h, as well as under various brake clamping forces (F B ). During dry tests, both pads exhibited high levels of COF. The mean value of average COF (μ m ) for the Cu-PM pad was 0.371, which was slightly higher than that of 0.358 from the Fe-PM pad. The stability of μ m over the IBS ranged from 68% to 82% for Cu-PM pads under different F B , while it was from 82% to 85% for Fe-PM pads. However, during the wet tests, the mean value of μ m dropped to 0.207 for Cu-PM pads, and with the minimum μ m of 0.062; whereas, they were 0.344 and 0.188 for Fe-PM pads, respectively, showing a significant difference in the friction performance between the two pads. Additionally, the W r of the Cu-PM pad was 0.110 cm 3 /MJ during dry tests, which was 17.3% lower than that of 0.133 cm 3 /MJ observed for the Fe-PM pad. After the brake test with the Cu-PM pad, the friction film primarily covered the Si/SiC-rich region of the disk, effectively inhibiting the plowing of SiC hard asperities onto the pad surface. However, the friction film predominantly covered the fiber-rich region of the disk after the test with the Fe-PM pad, and the exposure of hard Si/SiC-rich asperities would continuously plow the pad during braking and resulted in furrows on the surface of the Fe-PM pad. In terms of wear mechanisms, adhesion wear was the primary mechanism on the contact surfaces of the Cu-PM pad and the C/C-SiC disk, while abrasion dominated the interaction between the Fe-PM pad and the C/C-SiC disk. This study provides valuable insights for the application of C/C-SiC brake disks on trains.

Braking behaviors of Cu-based PM brake pads mating with C/C–SiC and 30CrMnSi steel discs under high-energy braking

Braking Performance of Fe-Based and Cu-Based Powder Metallurgy Pads Paired with C/C-SiC Disk on Full-Scale Dynamometer

Comparison of Braking Behaviors Between Iron- and Copper-Based Powder Metallurgy Brake Pads That Used for C/C–SiC Disc

Friction and Wear Mechanics of Fe-Based PM Pad Paired with Carbon Fiber-Reinforced Silicon Carbide (C/C-SiC) Disk Under High-Speed Braking

Effect of Cu Addition on the Braking Performance of Fe–Si Alloy-Modified C/C–SiC Brake Materials

Investigation on Braking Performance and Wear Mechanism of Full-Carbon/ceramic Braking Pairs

Modifying C/C–SiC brake pads with different Fe–Si alloy phases to improve the wear resistance of full-carbon/ceramic brake pair

Dry Sliding Wear Studies of Cu-Based Powder Metallurgy Brake Materials

Microstructure and tribological characteristics of needled C/C–SiC brake composites fabricated by simultaneous infiltration of molten Si and Cu

Braking behaviours of C/C-SiC mated with iron/copper-based PM in dry, wet and salt fog conditions

Tribological performance and composition optimization of semi-metallic friction materials applied for carbon ceramic brake disc

Tribological behavior and mechanism of h-BN modified copper metal matrix composites paired with C/C–SiC

Friction mechanism analysis of copper-based composites reinforced with ball-milled and modified composite ceramic powders

Microstructure and Tribological Properties of Cu Modified C/C- SiC Composites

Preparation and Tribological Properties of C/C–SiC Brake Composites Modified by in Situ Grown Carbon Nanofibers

Effect of carbon fiber on the braking performance of copper-based brake pad under continuous high-energy braking conditions

Study on the Particle-Reinforced Cu-Matrix Brake Pads for 300 Km·h-1 High-Speed Trains

Tribological Behavior and Mechanism of Carbon Fibre Reinforced Carbon and SiC Dual- Matrice Composites

Comparison of the Braking Behavior Among Cast Steel, Carbon/Carbon (C/C) and Carbon/Carbon-Silicon Carbide (C/C-SiC) Materials Mated with Copper-Based Composites

Oxidation Behaviour of C/C–SiC Brake Discs Tested on Full-Scale Bench Rig

Enhanced braking performance of copper metal matrix composites incorporating fine mosaic pitch coke when mated with 30CrMnVA and C/C-SiC