Abstract:Mg–6.0 Zn–2.0 Yb–0.5 Zr (wt.%) alloy exhibits excellent strength and ductility synergy after thermomechanical and heat treatment. Unfortunately, the hot workability and microstructure evolution under specific deformation regimes remain uncertain to date. In this work, the constitutive model and hot processing maps were established based on a series of isothermal compression tests. A detailed examination of deformation microstructures at different processing regimes revealed that the hot workability and correlated microstructure development were deformation condition dependent. When compressed at lower strain rates and higher deformation temperatures, the softening was promoted by dynamic recrystallization (DRX) and the prevalence of discontinuous dynamic recrystallization (DDRX) generally resulted in a complete DRX process with coarse grains and much-intensified texture. On the contrary, work hardening was improved with increasing dislocation density, and the continuous DRX (CDRX) may control the partial DRX progress, often presenting a much-refined microstructure with a more dispersed texture. Interestingly, a low strain rate of 0.001 s −1 and a moderate deformation temperature of 300 °C effectively balanced the nucleation rate and grain growth to finally achieve a much refined and relatively homogeneous grain structure. Further investigation concerning the activation energy suggested that the workability improved with increasing strain rate and temperature. Enhanced hot workability at most deformation regimes was achieved due to a lower average activation energy Q value in comparison with that of 1.0 wt.% Yb alloyed ZK60 counterpart, which was likely due to a higher activity of non-basal slips achieved in this alloy.

Processing maps for hot working of ZK60 magnesium alloy

Hot Deformation and Processing Map of As-Homogenized Mg–9Gd–3Y–2Zn–0.5Zr Alloy

Investigation into the Hot Workability of the As-Extruded WE43 Magnesium Alloy Using Processing Map

Processing Maps and Hot Compression Behaviors of ZK60 Alloy After Adding Different Rare Earth Elements

Constitutive Equation and Hot Processing Map of Mg-16Al Magnesium Alloy Bars

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Flow characterization of magnesium alloy ZK61 during hot deformation with improved constitutive equations and using activation energy maps

Experimental study of squeeze casting of ZK60 magnesium alloy

Flow Curve and Microstructure Analysis of a ZK60 Magnesium Alloy during Hot Compression Tests

Processing maps of extruded AZ80 + 0.4% Ce magnesium alloy

Construction of Dynamic Recrystallization Critical Strain Model, Kinetic Model, and Hot Workability of Mg–8Gd–4Sm–1Zn–0.5Zr Alloy

Hot workability and microstructure of Mg–6.0 Zn–2.0 Yb–0.5 Zr magnesium alloy

Hot Deformation Characteristics and Processing Parameter Optimization of Al–6.32Zn–2.10Mg Alloy Using Constitutive Equation and Processing Map

Microstructural and constitutive relationship in process modeling of hot working: The case of a 60Mg-30Pb-9.2Al-0.8B magnesium alloy

Hot Deformation Behavior and Processing Map of Coarse-Grained Mg–Gd–Y–Nd–Zr Alloy

Hot Deformation Behavior and Processing Map of Al-Zn-Mg-Cu-Zr Alloy

Thermal Deformation Behavior and Processing Maps of As-Homogenized Mg-5.8 Zn-0.5 Zr-1.0 Yb Alloy

Dynamic recrystallisation (DRX) map of magnesium alloy for texture control with hot processing

Unravelling the Hot Working Behavior, Constitutive Modeling, and Processing Map for Controlling the Microstructure of Sintered Al–Zn–Mg Alloy

Prediction of flow stress and microstructure evolution mechanism during thermal tensile process of ZK60 alloy

Dynamic recrystallization of a wrought magnesium alloy: Grain size and texture maps and their application for mechanical behavior predictions